5032190 BRACKET, REMOTE CABLE JOHNSON
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA
BRACKET
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
£39.42
18-09-2017
4.41[1.80] pounds
Connected : Connected Essentials
Connected Essentials 5032190 Tailored Heavy Duty Custom Fit Car Mats, for Mitsubishi L200 Double Cab (2006-), Grey with Blue Trim, Premium
Complete set of 4 tailored custom fit car mats - designed and manufactured specifically for Mitsubishi L200 Double Cab (2006-)||Supplied with clips (as applicable) for security||Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear||Manufactured from 650gram automotive quality carpet - for strength and durability||Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model.
Complete set of 4 tailored custom fit car mats - designed and manufactured specifically for Mitsubishi L200 Double Cab (2006-)||Supplied with clips (as applicable) for security||Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear||Manufactured from 650gram automotive quality carpet - for strength and durability||Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model.
BRP JOHNSON entire parts catalog list:
J25PL4SRS 2004
J30PL4SDR 2006
J30PL4SOC, J30TEL4SOC 2005
J30PL4SRS 2004
J30PL4SUA 2007
Information:
Illustration 1 g01302376
Typical schematic
Illustration 2 g01302383
P1 ECM connector
(P1-34) J1939 data link −
(P1-50) J1939 data link +
Illustration 3 g01302377
Service tool connector
(Terminal F) J1939 data link −
(Terminal G) J1939 data link + Test Step 1. Inspect Electrical Connectors and Wiring
Remove power from the ECM.
Thoroughly inspect the J1/P1 ECM connector and the J2/P2 ECM connector. Inspect all of the connectors that are associated with the circuit. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connectors that are associated with the circuit.
Check the allen head screw on each ECM connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and wiring for abrasion and for pinch points. Expected Result:All connectors, pins and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion or of pinch points.Results:
OK - The harness and wiring appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem in the wiring harness.Repair: Perform the following repair:Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Refer to Troubleshooting, "Electrical Connectors - Inspect".Verify that the repair eliminates the problem.STOPTest Step 2. Verify the Proper Installation of the Data Link Circuit
Disconnect any module that is connected to the CAN data link.
Disconnect J1/P1 ECM connector and measure the resistance between P1-50 (CAN Data Link +) and P1-34 (CAN Data Link -). Expected Result:The resistance is between 57 and 63 Ohms.Results:
OK - The resistance is within the range. Proceed to Test Step 5.
Not OK - The range of the resistance is 114 Ohms to 126 Ohms. A terminating resistor is missing.Repair: Verify that two terminating resistors exist on the data link. One resistor must be located on each end of the data link.STOP
Not OK - Resistance is less than 57 Ohms. Proceed to Test Step 3.
Not OK - Resistance is greater than 126 Ohms. Proceed to Test Step 4.Test Step 3. Check for a Short Circuit
Disconnect the J1/P1 ECM connector.
Remove the terminating resistors from the CAN data link.
Measure the resistance from the following pins to every pin on ECM connector P1 and to engine ground.
P1-50 (CAN Data Link +)
P1-34 (CAN Data Link -)Expected Result:Each resistance measurement indicates an open circuit.Results:
OK - There are no shorts. Proceed to Test Step 4.
Not OK - A short exists in the wiring harness.Repair: Make the necessary repairs.Verify that the repair eliminates the problem.STOPTest Step 4. Check for an Open Circuit
Make sure that all connections remain disconnected.
Fabricate a jumper wire. Use the jumper wire in order to short pin F to pin G on the service tool connector.
Measure the resistance between P1-50 (CAN Data Link +) and P1-34 (CAN Data Link -) at the ECM connector.
Remove the wire short. Expected Result:The resistance measurement indicates a short circuit.Results:
OK - There is not an open circuit. Proceed to Test Step 5.
Not OK - An open circuit exists in the wiring harness.Repair: Make the necessary repairs.Verify that the repair eliminates the problem.STOPTest Step 5. Check the Module on the CAN Data Link
Connect the module to another engine.
If the module operates properly on a different engine, there may be a problem with the ECM.
If the module does not function properly on the different engine, replace the module. Expected Result:The module operates properly.Results:
OK - The module operates properly on another engine.Repair: The problem may be intermittent. If the problem is intermittent, refer to Troubleshooting, "Electrical Connectors - Inspect".STOP
Not OK - The module does not operate properly on another engine.Repair: Replace the module. Verify that the repair corrects the problem.STOP
Parts bracket JOHNSON:
5032048
5032048 BRACKET, RELAY
J10EL4SRC, J10R4SNF, J10R4SR, J10R4STC, J15R4SNF, J15R4SR, J15R4STC, J15RL4SR, J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
5032400
5032400 *BRACKET
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
5032302
5032302 *BRACKET, REAR FASTENER
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
5032351
5032351 BRACKET, CONNECTOR HOLDER
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
5034709
5034709 BRACKET, LOWER MOUNT (WHITE)
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
5031952
5031952 BRACKET, ROCKER ARM SHAFT
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
5031953
5031953 BRACKET, ROCKER ARM SHAFT
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
5035784