5032919 JOHNSON BRACKET, Steering


5032919 BRACKET, Steering JOHNSON BJ60PL4SRR, BJ60PL4STC, BJ70PL4SRR, BJ70PL4STC, J60PL4SNF, J70PL4SNF BRACKET
5032919 BRACKET, Steering JOHNSON
Rating:
83

Buy BRACKET, Steering 5032919 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 7
 

BRP JOHNSON entire parts catalog list:

BJ60PL4SRR, J60PL4SRR 2004
BJ60PL4STC, J60PL4STC 2003
BJ70PL4SRR, J70PL4SRR 2004
BJ70PL4STC, J70PL4STC 2003
J60PL4SNF 2002
J70PL4SNF 2002

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
B 1U-6683 Ring Expander 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03003219
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Position the spring for oil control ring (3) into the oil ring groove in piston (4). The central wire must be located inside the end of the spring.
Position the oil control ring with the word "TOP" in the upward position. Use Tooling (B) to install oil control ring (3) over the piston and the spring. Note: Ensure that the central wire is 180 degrees from the ring gap.
Use Tooling (B) to install intermediate compression ring (2) into the second groove in piston (4). The word "TOP" must be upward.
Use Tooling (B) to install top compression ring (1) into the top groove in piston (4). The word "TOP" must be upward.
Position the piston ring gaps at approximately 120 degrees away from each other. Note: A new piston assembly is supplied with new piston rings.
Illustration 2 g03001779
(A) Cut away for piston cooling jet
(9) Upper shell for connecting rod
(X) Identification marks
(Y) Location tag on connecting rod shells
(Z) Location tag in connecting rod for shells (not shown)
(10) Lower shell for connecting rod cap
Use Illustration 2 as an assembly guide.
Illustration 3 g03001216
Lubricate bushing (8) for piston pin (6) in the connecting rod with clean engine oil. Lubricate the bore for the piston pin in piston (4) with clean engine oil.
Install piston pin (6) to piston (4). Note: If the piston pin cannot be installed by hand, heat the piston to a temperature of 45° 5°C (113° 9°F).
Use Tooling (A) in order to install circlips (5) to the piston pin bore in piston (4). Note: Ensure that the circlips are seated in the grooves in the piston.
Install upper bearing shell (9) into connecting rod (7). Ensure that the locating tab for the upper bearing shell is correctly seated in slot in the connecting rod.
Install lower bearing shell (10) into connecting rod cap (11). Ensure that the locating tab for the lower bearing shell is correctly seated in the slot in the connecting rod cap.
Temporarily install connecting rod cap (11) and bolts (12) to connecting rod (7) when the assembly is out of the engine. Ensure that the etched number on connecting rod cap matches the etched number on connecting rod. Ensure the correct orientation of the connecting rod cap. The locating tab for the upper bearing shell and the lower bearing shell should be on the same side. Tighten bolts (12) to a torque of 20 N m (177 lb in).
Repeat Step 1 through Step 13 for the remaining piston and connecting rod assemblies. Note: Fracture split connecting rods should not be left without the connecting rod caps installed.End By:
Install the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Install" for the correct procedure.


Parts bracket JOHNSON:

5030820
BRACKET, Connector
5030820 BRACKET, Connector
BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SDM, BJ70PL4SOA, BJ70PL4SRR, BJ70PL4STC, J60PL4SNF, J70FLTLECS, J70PL4SNF
5032902
 
5032902 BRACKET, Silencer
BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SDM, BJ70PL4SOA, BJ70PL4SRR, BJ70PL4STC, J60PL4SNF, J70PL4SNF
5032855
 
5032855 BRACKET, Neutral switch
BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SDM, BJ70PL4SOA, BJ70PL4SRR, BJ70PL4STC, J60PL4SNF, J70PL4SNF
5031148
*BRACKET, Engine cover
5031148 *BRACKET, Engine cover
BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SDM, BJ70PL4SOA, BJ70PL4SRR, BJ70PL4STC, J60PL4SNF, J70PL4SNF
5032928
 
5032928 BRACKET, Lower mount
BJ60PL4STC, BJ70PL4STC, J60PL4SNF, J70PL4SNF
5034530
 
5034530 BRACKET, Lower mount
BJ60PL4SRR, BJ70PL4SRR
5034519
 
5034519 BRACKET, Clamp Stbd
BJ115L4SDA, BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ70PL4SDM, BJ70PL4SOA, BJ70PL4SRR, BJ90PL4SDA, J115PL4SOR, J90PL4SOR
5034520
 
5034520 BRACKET, Clamp - Port
BJ60PL4SRR, BJ70PL4SRR
Back to top