5036916 JOHNSON BRACKET, THROTTLE CABLE


5036916 BRACKET, THROTTLE CABLE JOHNSON BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC BRACKET
5036916 BRACKET, THROTTLE CABLE JOHNSON
Rating:
18

Buy BRACKET, THROTTLE CABLE 5036916 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

BRP JOHNSON entire parts catalog list:

BJ25E4SDS, BJ25EL4SDS, J25E4SDC, J25EL4SDC 2006
BJ25E4SUC, BJ25EL4SUC, J25E4SUR, J25EL4SUR 2007
BJ25R4SDS, BJ25RL4SDS, J25R4SDC, J25RL4SDC 2006
BJ25R4SUC, BJ25RL4SUC, J25R4SUR, J25RL4SUR 2007
BJ25TE4SDS, BJ25TEL4SDS, J25TE4SDC, J25TEL4SDC 2006
BJ25TE4SUC, BJ25TL4SUC, J25TE4SUR, J25TEL4SUR 2007

Information:


Illustration 1 g01303631
Schematic for the analog sensor
Test Step 1. INSPECT THE ELECTRICAL CONNECTORS AND WIRING
Remove the electrical power from the engine. Note: For the following steps, refer to Troubleshooting, "Electrical Connectors - Inspect".
Thoroughly inspect each of the following connectors:
J1/P1 connectors
J7/P7 connectors
Check the torque of the allen head screws for the ECM connectors.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit for the analog sensors.
Check the harness and wiring for abrasion and for pinch points from the analog sensors to the master ECM. Expected Result:All connectors, pins, and sockets are connected properly. The connectors and the wiring do not have corrosion, abrasion, or pinch points.Results:
OK - All connectors, pins, and sockets are connected properly. The connectors and the wiring do not have corrosion, abrasion, or pinch points. The components are in good condition with proper connections. If you are troubleshooting a -3 code, proceed to Test Step 3. If you are troubleshooting a -4 code, proceed to Test Step 2.
Not OK - At least one of the connectors, pins, and/or sockets are not connected properly. At least one of the connectors and/or the wiring has corrosion, abrasion, or pinch points.Repair: Perform the necessary repairs and/or replace parts, if necessary.STOPTest Step 2. CREATE AN OPEN CIRCUIT FOR THE SENSOR
Disconnect the sensor that has the "voltage below normal" diagnostic code.
Observe the "Active Diagnostic" screen on Cat ET. Allow a minimum of 30 seconds for any codes to activate. Look for an active -3 diagnostic code. Expected Result:There is an active -3 diagnostic code for the disconnected sensor.Results:
Yes - Before the suspect sensor was disconnected, there was an active -4 diagnostic code for the sensor. After the suspect sensor was disconnected, there was an active -3 diagnostic code for the sensor.Repair: Reconnect the sensor. If the active -4 diagnostic code recurs, replace the original sensor.Verify that the code does not activate when the new sensor is installed. Clear the logged codes from the master ECM.STOP
No - Before the suspect sensor was disconnected, there was an active -4 diagnostic code for the sensor. After the suspect sensor was disconnected, the active -4 diagnostic code remained. Proceed to Test Step 3.Test Step 3. CHECK THE PULL-UP VOLTAGE AT THE SENSOR
Verify that the suspect sensor's connector is disconnected from the engine harness.
Illustration 2 g01303636
Harness connectors for the sensor
(1) Signal
(2) Return
At the harness connector for the suspect sensor, measure the voltage between terminals (1) and (2). Expected Result:The voltage is between 6.0 VDC and 7.0 VDC.Results:
OK - The voltage between the signal terminal and the return terminal is between 6.0 VDC and 7.0 VDC. The pull-up voltage that is created by the master ECM is present at the sensor connector. The signal wire and the return wire for the suspect sensor appear to be OK. Proceed to Test Step 5.
Not OK - The voltage between the signal terminal and the return terminal is not between 6.0 VDC and 7.0 VDC. The pull-up voltage that is created by the master ECM is not present at the sensor connector. Proceed to Test Step 4.Test Step 4. CHECK THE PULL-UP VOLTAGE AT THE MASTER ECM
Use a 151-6320 Wire Removal Tool to remove the signal wire for the suspect sensor from the P1 connector.
Use a jumper wire with


Parts bracket JOHNSON:

5033805
 
5033805 *BRACKET, PLANET GEAR
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, BJ25E4SDS, BJ25E4SUC, BJ25TE4SDS, BJ25TE4SUC, BJ40PL4SDR, BJ40PL4SOC, BJ50PL4SDR, BJ50PL4SOC, BJ90PL4SDA, BJ90PL4SRC
5036978
 
5036978 BRACKET, Starter motor
BJ25E4SDS, BJ25E4SUC, BJ25TE4SDS, BJ25TE4SUC
5037032
 
5037032 BRACKET, Lower mount
BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC
5036892
 
5036892 BRACKET, FUEL FILTER
BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC
5036893
 
5036893 BRACKET, FUEL FILTER
BJ115L4SDA, BJ140CX4DR, BJ140L4SDR, BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC, BJ90PL4SDA
5036998
 
5036998 BRACKET, CLAMP STBD (WHITE)
BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC
5037163
 
5037163 BRACKET, CLAMP PORT (WHITE)
BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC
5037158
 
5037158 BRACKET, SWIVEL - 20"
BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC
Back to top