0554334 JOHNSON BUMPER,Exhaust tube


0554334 BUMPER,Exhaust tube JOHNSON 33E69A, 33E69A, 33E70M, 33E70M, 40E71B, 40E72E, 40E73D, 40E74S, 40E75C, 40E76A, J40RSLR, J40RWCDB, J40RWCOM, J40RWCRA, RX-16M BUMPER
0554334 BUMPER,Exhaust tube JOHNSON
Rating:
53

Buy BUMPER,Exhaust tube 0554334 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$17.94
 

07-06-2021
0.2[0.00] Pounds
-: -
Johnson Evinrude OMC New OEM Exhaust Tube Bumper 0554334, 554334
SKU: 0554334 || Sold Each || Please verify your own fitment
Number on catalog scheme: 65
 

BRP JOHNSON entire parts catalog list:

33E69A, 33EL69A, 33R69A, 33RL69A 1969
33E69A, 33EL69A, 33R69A, 33RL69A 1969
33E70M, 33EL70M, 33R70M, 33RL70M 1970
33E70M, 33EL70M, 33R70M, 33RL70M 1970
40E71B, 40E71G, 40EL71B, 40EL71G, 40R71B, 40R71G, 40RL71B, 40RL71G 1971
40E72E, 40EL72E, 40R72E, 40RL72E 1972
40E73D, 40EL73D, 40R73D, 40RL73D 1973
40E74S, 40EL74S, 40R74S, 40RL74S 1974
40E75C, 40EL75C, 40R75C, 40RL75C 1975
40E76A, 40E76R, 40EL76A, 40EL76R, 40R76A, 40R76R, 40RL76A, 40RL76R 1976
J40RSLR, J40RSR, J40RWCTR, J40RWLCTR 1983
J40RWCDB, J40RWLCDB 1986
J40RWCOM, J40RWLCOM 1985
J40RWCRA, J40RWLCRA 1984
RX-16M, RX-16R, RXE-16M, RXE-16R, RXEL-16M, RXEL-16R, RXL-16M, RXL-16R 1968

Information:


When holding the bellows ensure that no excessive stress is induced on it. The bellows must be supported always when the bellows are not installed in the application. Failure to support the bellows adequately could result in the failure of the bellows. Do not use power tools to disassemble or assemble any part of the flexible exhaust system.The alignment of the bellows is important. Incorrect alignment may lead to premature failure of the bellows and possible emissions failure. Misalignment can be identified by visually inspecting the uniformity of the spacing between the convolutions on the bellows.Inspect the bellows for damage prior to installation. If there is any damage to the convolutions, discard the bellows. If there is any difficulty in installation after the repair, discard the bellows.
Illustration 1 g06369006
Typical example
The lateral alignment of the bellows is critical. All the components must be assembled in the same alignment as prior to disassembly. The components that require correct lateral alignment are shown at Positions (A) and (B).
Illustration 2 g06368998
Typical example
Follow Step 2a through Step 2d to remove the flexible exhaust (6) as an assembly from the Clean Emission Module (CEM) and the turbocharger.
Use suitable material to encase exhaust pipe bellows (3). Encasing the exhaust pipe bellows will prevent damage. Encase between Position (C) and Position (D). Use cable straps to retain the suitable material.Note: Ensure that the flexible exhaust pipe is supported always.
Loosen ball clamp (2) from the flexible exhaust pipe assembly.
Loosen the bolt for V-band clamp (4).Note: If V-band clamp (4) remain tight on the flanges, apply releasing fluid on the V-band clamp. Lightly tap the bolt on the V-band clamp with a soft faced hammer to assist removal. Do not use a prybar to remove V-band clamp.
Remove the assembly of the flexible exhaust pipe from the exhaust back pressure valve (5) first and then from CEM (1).Note: Ensure that the assembly of the flexible exhaust pipe is supported as the clamps are removed.Installation Procedure for the Flexible Exhaust Pipe as an Assembly
Inspect the bellows for damage prior to installation. If there is any damage to the convolutions, discard the bellows. If there is any difficulty in installation after the repair, discard the bellows.
Failure to reinstall the bellows into the original position will result in a failure of the bellows and possible emissions failure.
Check the flexible exhaust pipe assembly for damage. Refer to your Caterpillar dealer for further information.
Illustration 3 g06368998
Typical example
Position a new ball clamp (2) onto the flexible exhaust pipe assembly (6).
Install V-band clamp (4) onto exhaust back pressure valve (5).
Install the assembly of the flexible exhaust pipe first onto CEM (1) and then on the exhaust back pressure valve (5).Note: Ensure that the assembly of the flexible exhaust pipe is supported always and the bellows is not subjected to any undue stress. Ensure correct alignment of all components.
Tighten V-band clamp (4) hand tight.
Tighten ball clamp (2) hand tight.
Illustration 4 g06368998
Typical example
Tighten ball clamp (2) to a torque of 35 N m (26 lb ft).
Tighten V-band clamp (4) to a torque of 12 N m (106 lb in).
Cut cable straps from the suitable material that was encasing the bellows (3) between Position (C) and Position (D). Remove the suitable material from bellows (3).


Parts bumper JOHNSON:

0305365
 
0305365 BUMPER,Tilting,swivel bracket
33E69A, 33E69A, 33E70M, 33E70M, 40E69R, 40E70A, 40E71B, 40E72E, 40E73D, 40E74S, 40E75C, 40E76A, 40ES69R, 40ES70A, 40R69R, 40R70A, J40RSLR, J40RWCDB, J40RWCOM, J40RWCRA, RD-30A, RDS-30A, RK-30A, RX-16M
0203290
 
0203290 BUMPER, ANCHOR & PIN ASSY.
115EL77S, 115ESL74B, 115ESL75E, 135ESL74B, 135ESL75E, 33E69A, 33E69A, 33E70M, 33E70M, 40E71B, 40E72E, 40E73D, 40R69R, 40R70A, 70EL76D, 70EL77S, 70ES74M, 70ES75B, 75ELR76D, 75ELR77S, 75ESLR75B, 85EL76D, 85EL77S, 85ESL74B, 85ESL75E, RD-30A
0314416
BUMPER, Spark advance
0314416 BUMPER, Spark advance
100ESL71A, 100ESL72R, 100ML79S, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 175TL77S, 175TL7
0315159
 
0315159 BUMPER, Locating brackets
100ESL71A, 100ESL72R, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 150TL78S, 175TL77S, 175TL78C, 200TL76S, 200TL77C, 200TL78R, 235TL7
Back to top