0315636 JOHNSON BUSHING

Table 1
Diagnostic Codes Table    
Code and Description    Conditions which Generate this Code    System Response    
3243-9 Water Pump Control Module: Abnormal Update Rate     There is a loss of communication on the CAN A data link between the engine ECM and the Electric Water Pump Controller (EWPC).     The code is logged.    
Illustration 1 g02371597
Typical schematic
Illustration 2 g02029218
Typical schematic
The Power Train Electric Drive System and the Accessory Power System will contain hazardous voltage levels during machine operation and for a period of time after machine shutdown.Do not remove any covers that will expose energized electrical components while the engine is operating. Do not remove any covers that will expose the energized electrical components while the components remain energized following an engine shutdown.Do not perform any type of electrical maintenance on the orange hazardous voltage conductors, the power train components or the accessory power system components while the engine is operating.Do not perform any type of electrical maintenance on the orange hazardous voltage conductors, the power train components or the accessory power system components while the components remain energized following an engine shutdown.Always perform the safe shutdown and de-energizing procedure before performing electrical service on the Power Train Electric Drive System or the Accessory Power System.Failure to follow these instructions could result in personal injury or death.
In order to avoid the build up of hazardous live voltages on the exposed surfaces, all grounding wires must be properly connected at all times during engine operation.Any disconnected grounding wires (including the grounding bond wires, the conductor shield wires, the power inverter grounding straps and the component housing grounding straps) must be properly reconnected before the engine is started.Failure to follow these instructions could result in personal injury or death.
Note: Always perform the procedure for safe shutdown and de-energizing before performing electrical service on the Power Train Electric Drive System or the Accessory Power System. The procedure will verify that the voltage in the power train electrical system has been discharged to less than 50.0 VDC. Refer to the Specifications, Systems Operation, Troubleshooting, Testing and Adjusting, "Electrical Maintenance Guidelines" for the proper procedure.Note: A multimeter must be used to verify that there is little or no voltage present at the exposed conductors before any other action is taken. Manually measure the voltage in order to confirm the voltage to be at a low level (50.0 VDC or less).Test Step 1. Inspect Electrical Connectors And WiringNote: Carefully following this procedure is a good way to identify an intermittent problem.
Illustration 3 g01415758
Location of the engine ECM
Perform a visual inspection of the wiring between the engine P1 connector and the EWPC. Look for these problems:
Harness damage that is caused by chafing
Harness damage that is caused by excessive heat
Inspect the P1 connector:
Look for moisture on the wiring and on the connector.
Illustration 4 g02029236
Terminal locations at the P1 engine ECM that are for the data link (P1-34) CAN data link - (P1-48) +Battery (P1-50) CAN data link + (P1-53) +Battery (P1-61) -Battery (P1-63) -Battery (P1-65) -Battery (P1-70) Keyswitch
Pull on the wires that are associated with the data links. Verify that the wire is properly crimped to the terminal and that the terminal is properly inserted into the connector.
Illustration 5 g02029261
EWPC at the rear of the engine compartment on the upper right side (1) System power and control circuit connector
Inspect the EWPC connector:
Look for moisture on the wiring and on the connector.Expected Result:All connectors, pins, and sockets are coupled and/or inserted and the harness and wiring are free of corrosion, of abrasion or of pinch points.Results:
OK - The wiring and the connectors appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem with the wiring or with a connector.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are coupled. Verify that the problem is resolved.STOPTest Step 2. Check the CAN A Data Link Between the Engine ECM and the EWPCNote: Always perform the procedure for safe shutdown and de-energizing before performing electrical service on the Power Train Electric Drive System or the Accessory Power System.The procedure will verify that the