0335521 JOHNSON BUSHING, Shift lever to block

5P2160 Engine Horsepower Meter Arrangement
5P2149 ATTACHMENT GROUP 1. 5P2146 Case Assembly2. 2P2288 Adapter (3)3. 7M7440 Plug (4)4. 5P2148 Flowmeter Assembly5. 9S4167 Stud6. 2P2289 Adapter7. 1L1644 Nipple (2)8. 3P2235 Nipple (2)9. 4D6320 Hose Assembly10. 4J5267 Seal (11)11. 6F8146 Seal (11)12. 5P2156 Clamping Bracket13. 5P2155 Solenoid Valve14. 5P7360 Tachometer Generator15. 9S211 Clamp (2)16. 9S3032 Clamp (2)17. 5P6520 Electric Fuel Pump (not part of 5P2149 Grp) 5P1759 Tachometer Drive Group (consisting of):18. 9N641 Adapter Group19. 5P1758 Shaft Assembly20. 4N538 Coupling21. 4M8303 Seal22. 2P2270 Accumulator Group23. 5P2963 Charging Adapter 4J7533 Seal (included with accumulator)24. 3H2891 Tee25. 3P2234 Nipple (2)26. 1S2237 Hose Assembly (3)27. 3P2232 Coupler (2)28. 3B7284 Nipple29. 2P5508 Adapter (2)30. 3P2236 Nipple (4)31. 3P1531 Adapter (2)32. 2P5511 Plate33. 5S2403 Fitting (2)34. 9M1697 Adapter35. 3J7354 Seal (included with adapter)36. 617921 Connector37. 4L8144 Gasket (6)38. 4F5639 Gasket (6)39. 5P2157 Fuel Meter Cable40. 5P2159 Tachometer Cable41. 5P4193 Battery Charging Cable (Use 5P2158 Cable for serial numbers 1001 - 1104.)42. 5P2161 Solenoid Cable43. Data Sheets Form 01-774-82695-1
All hoses are a special rubber that is resistant to oil and diesel fuel. Do not substitute another type of hose; damage to the fuel flowmeter and engine fuel system may result. The minimum inside diameter of all fittings and hoses must be 3/8" (9.5).
4. 5P2148 Fuel Flowmeter (complete)44. 3P2233 Coupler (2) 5P4179 Fuel Flowmeter Repair Kit (not shown) (replacement seals)
45. 5P2150 Engine Horsepower Meter (complete) 5P2152 Digital Board Assembly 5P4187 Power Board Assembly (Use 5P2165 Power Board Assembly for serial numbers 1001 - 1104.) 8M8283 Seal (6 or 9 used)46. 2S6024 Fuse (2) 5 amp - Bussman AGC547. 5P2175 Battery (2 used in serial no. 1001 - 1104)48. Wrench (not serviced, for knob setscrews)Required Additional Parts For Some Applications
Use a 2P8292 Box for storage and transportation of the following special purpose tools and adapters.
Tachometer Drive Adapters The 5P1759 Tachometer Drive (included in the 5P2149 Attachment Group) is to be used on all engines equipped with ENM Service Meters. When used on engines with sleeve metering, two 9S211 Clamps are needed for mounting.1. 5S6106 Adapter (2:1 decrease drive ratio - for engines using 7M6001 Adapter Group)2. 6B344 Adapter (1:2 increase drive ratio)3. 6B3124 Adapter (Right Angle - 1:1 drive ratio)4. 5L2277 Tee Adapter (1:1 drive ratio - for operating two tachometers at the same time)5. 1P7448 Cable Assembly (Use where there is not enough clearance to connect the tachometer adapter directly to the Service Meter drive unit. Do not bend the cable sharply. The cable assembly is part of the 4S6553 Instrument Group)6. 1M5061 Tachometer Drive Group (Used for current 988 and 992 Wheel Loaders. Used with the 9S2000 Hydraulic Flowmeter.)7. 5P935 Adapter Group (Use on D3, 910, 931. The 7M6006 Adapter Group is part of the 7M6001 Adapter Group.)8. 7M6006 Adapter Group (Use on D3, 910, 931. The 7M6006 Adapter Group is part of the 7M6001 Adapter Group.)
FT1188 Fuel Line Adapter (For checking fuel pressure, fuel temperature, and air in the fuel. Also includes valve for sampling fuel and bleeding.) 9. 3P2233 Coupler10. 2P8278 Flow Tube11. 4B6067 Elbow12. 8L6005 Tee13. 2F7112 Thermometer14. 3B9068 Valve15. 8M2744 Gauge16. 3P2236 Nipple17. 5B1311 Nipple (Reworked as shown)18. 6B2982 Tee (Reworked as shown)19. 3B7722 Bushing
FT998 Adapter - Make from 9S4165 Cover Assembly. (For D348 and D349 vehicular engines.)
FT999 Adapter - Make from 8H628 Cover Assembly. (For certain D342 and D339 engines)
FT1000 Adapter - Make from 5M476 Cover Assembly. (For certain earlier D311, D320, D330, D333, 1670 and 1673 engines)
FT1019 Adapter - Make from 1S1961 Cover Assembly. (For 621 (23H) and 980 (42H) applications)
For certain earlier engines (and later engines without spin-on fuel filters), it is necessary to rework the fuel filter housing cover in order to measure the fuel flow. The above drawings show a typical cover and a reworked adapter cover. Before making an adapter cover, be sure to verify fuel flow direction.The following parts are required for the purpose noted. Use adapter (A) and a 1M5829 Gasket at the fuel filter housing on 5.4" bore and 6 1/4" bore inline engines. Use adapter (B) and a 4L8132 Gasket at the fuel injection housing on 6 1/4" bore "V" engines. Bend the 3N1952, 3N1953 or 3N1954 Tube Assembly as shown before cutting it to the length shown at each end. At fitting (1), loosen the braze and rotate the tube 90°. Drill out two 1H7724 Bushings to .500"(12.70); solder the bushings to the cut tubing, then install the 3P2235 Nipples. Use adapter (C) and a 4L8144 Gasket at the fuel injection housing on 5.4" bore "V" engines. Bend the 3N4504, 3N4506, or 3N4508 Tube Assembly as shown, then cut it to the length shown. Drill out a 1H7724 Bushing to .500" (12.70), then solder the bushing to the cut tubing. Install a 3P2235 Nipple.Replacing And Charging The Batteries
Always turn off the Horsepower Meter before removing or installing the face panel.
(1) Remove six screws (1). Lift panel (2) clear of the case.
Be careful not to damage the panel or two switches (3) when removing the panel. Disconnect plug (4) and vent tube (5) from plate (6). Disconnect the wires from the batteries, and remove plate (6). Remove the old batteries. Put the new batteries in position in the case with the positive (red) terminals at locations (A).
Earlier Horsepower Meters do not use third battery (7) shown. (2) Make sure the 8M8283 O-ring seals are in position in plate (6). Install plate (6) so the