5033661 JOHNSON CAMSHAFT, EXHAUST - 115HP


5033661 CAMSHAFT, EXHAUST - 115HP JOHNSON BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ90PL4SDA, BJ90PL4SRC, BJ90PL4STS, J115PL4SOR, J90PL4SOR CAMSHAFT
5033661 CAMSHAFT, EXHAUST - 115HP JOHNSON
Rating:
53

Buy CAMSHAFT, EXHAUST - 115HP 5033661 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$38.88
 

02-12-2023
0.0013[0.00] Pounds
LU: Amazon Global Store
Nk 5033661 Axial Joint, Tie Rod
NK Length [mm]: 316 || Thread Size: 12x1,5 || Thread Type: with right-hand thread
Number on catalog scheme: 2
 

BRP JOHNSON entire parts catalog list:

BJ115L4SDA, BJ115PX4SDA, J115PL4SDA, J115PX4SDA 2006
BJ115L4SRC, BJ115X4SRC, J115PL4SRC, J115PX4SRC 2004
BJ115L4STS, BJ115X4STS, J115PL4STS, J115PX4STS 2003
BJ90PL4SDA, BJ90PX4SDA, J90PL4SDA, J90PX4SDA 2006
BJ90PL4SRC, BJ90PX4SRC, J90PL4SRC, J90PX4SRC 2004
BJ90PL4STS, BJ90PX4STS, J90PL4STS, J90PX4STS 2003
J115PL4SOR, J115PX4SOR 2005
J90PL4SOR, J90PX4SOR 2005

Information:

Recommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in the order of the listed test steps.
Table 1
Troubleshooting Test Steps    Values    Results    
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Look for active codes that are associated with the system for the event code.
   
Codes
   
Result: An associated code is active.
Repair: Troubleshoot any associated codes before continuing with this test.
Result: A code is active or logged.
Proceed to Test Step 2.
   
2. Check for Incorrect Parameters
A. Use Cat ET to verify that the correct parameters are being used. Refer to Troubleshooting, "Configuration Parameters" for additional information.
   
Parameters
   
Result: The correct parameters are being used.
Proceed to Test Step 3.
Result: The correct parameters are not being used.
Repair: Configure the correct parameters.
Verify that the repair eliminated the problem.
   
3. Inspect the Air Shutoff System (if applicable))
A. Check for proper operation of the air shutoff system. Refer to Troubleshooting, "Air Shutoff - Test".
   
Air Shutoff
   
Result: The air shutoff is operating correctly.
Proceed to Test Step 4.
Result: The air shutoff is not operating correctly.
Repair: Make the necessary repairs.
Verify that the repair eliminated the problem.
   
4. Check the Fuel System
A. Visually check the fuel level in the fuel tank. Do not rely on the fuel gauge only.
B. Ensure that the fuel supply valve (if equipped) is in the full OPEN position.
C.. Inspect the fuel system. Refer to Systems Operation/Testing and Adjusting, "Fuel System - Inspect" for additional information.
Cold weather adversely affects the characteristics of the fuel. Refer to the engines Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold-weather operation.
D. Check fuel quality. Refer to Systems Operation/Testing and Adjusting, "Fuel Quality - Test" for the proper procedure. Check the fuel tank for debris or foreign objects which may block the fuel supply.
E. Check the filtered fuel pressure while the engine is being cranked. Refer to Troubleshooting, "Fuel Pressure Is Low" for the proper testing procedure.
   
Fuel System
   
Result: The fuel system is operating properly.
Proceed to Test Step 5.
Result: The fuel system is not operating properly.
Repair: Make the necessary repairs.
Verify that the repair eliminates the problem.
   
5. Test the Fuel Injectors
If service has been performed on the engine fuel system recently, verify that the injector trim files are correct. Use Cat ET to check that the injector trim files are correct for the injectors that are installed on the engine.
A. Perform the "Injector Solenoid Test" on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM.
B. Access the "Cylinder Cutout Test" in the "Diagnostic Tests" under the "Diagnostics" menu.
C. Perform the "Automatic Cylinder Cutout Test" on Cat ET.
   
Fuel Injector
   
Result: The test was successful.
Proceed to Test Step 6.
Result: The test was not successful.
Repair: Diagnose the problem and then repair the problem.
Reset all active codes and clear all logged codes.
Verify that the repair eliminated the problem.
   
6. Check the Engine Accessories
A. Inspect any engine accessories and the transmission (if applicable).
   
Engine Accessories
   
Result: An engine accessory is creating an excessive load.
Repair: Repair the engine accessory.
Verify that the repair eliminated the problem.
   


Parts camshaft JOHNSON:

5033660
 
5033660 CAMSHAFT, INTAKE - 115HP
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ90PL4SDA, BJ90PL4SRC, BJ90PL4STS, J115PL4SOR, J90PL4SOR
5033901
 
5033901 CAMSHAFT, INTAKE - 90HP
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ90PL4SDA, BJ90PL4SRC, BJ90PL4STS, J115PL4SOR, J90PL4SOR
5033902
 
5033902 CAMSHAFT, EXHAUST - 90HP
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ90PL4SDA, BJ90PL4SRC, BJ90PL4STS, J115PL4SOR, J90PL4SOR
Back to top