5033917 JOHNSON CAMSHAFT, INTAKE

Table 1
Diagnostic Codes Table    
Code and Description    Conditions which Generate this Code    System Response    
168-3 Battery Potential / Power Input #1 : Voltage Above Normal     Electrical System Voltage : Voltage Above Normal     The code is logged.    
168-4 Battery Potential / Power Input #1 : Voltage Below Normal     Electrical System Voltage : Voltage Below Normal     The code is logged.    The engine ECM requires the keyswitch to be in the ON position in order to maintain communications with Cat® Electronic Technician (Cat® ET).
Illustration 1 g03367711
Schematic
Illustration 2 g03156496
Machine interface connector (1) + Batt (3) + Batt (7) Keyswitch
Table 2
1. Inspect the Electrical Connectors and the Wiring
A. Turn the main disconnect switch to the OFF position.
B. Thoroughly inspect the ECM connectors. Also, thoroughly inspect the other connectors for the electrical power circuit. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the proper procedure for inspecting the connectors and the wiring.
   
Electrical connectors    
Results: The connectors and wiring appear to be OK.
Proceed to Test Step 2.
Results: There is a problem in the connectors and/or wiring.
Repair The connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are coupled.
Verify that the repair eliminated the problem.
   
2. Check the Voltage to the ECM
A. Disconnect the ECM connector J1/P1.
B. Restore the electrical power to the ECM.
C. Measure the voltage at the ECM. Measure the voltage between P1-53 and P1-65. Measure the voltage between P1-52 and P1-63.
   
ECM voltage    
Result: The voltage is 24 3 VDC.
The ECM is receiving the correct voltage. The problem may be intermittent. If the problem is intermittent, refer to Troubleshooting, "Electrical Connectors - Inspect".
Result: The voltage is less than 24 3 VDC.
The wiring or components between the battery and the ECM may be preventing the voltage from reaching the ECM.
Proceed to Test Step 3
   
3. Check the Charging Circuit
A. Turn the main disconnect switch to the OFF position.
A. Check the charging circuit.
   
Charging circuit    
Result: The charging system is OK.
Proceed to Test Step 4.
Result: The charging system is not OK.
There is a problem with the charging system. Make the necessary repairs. Refer to Special Instruction, REHS0354, "Charging System Troubleshooting".
Verify that the repair eliminated the problem.
   
4. Load Test the Battery
A. Load-test the battery. Refer to Systems Operation and Testing and Adjusting, "Battery - Test"
   
Load test    
Result: The battery voltage is low or the battery did not pass the load test.
Repair: Recharge or replace the faulty batteries.
Verify that the repair eliminated the problem.
Result: The batteries pass the load test. The measured voltage is between 11.5 VDC and 13.5 VDC for a 12 v system. The measured voltage is between 23.0 VDC and 27.0 VDC for a 24 v system.
Proceed to Test Step 5
   
5. Check the Voltage at the Engine Interface Connector (EIC)
A. Disconnect the EIC..
B. Restore the electrical power to the ECM.
C. Measure the voltage from terminal 1 to the -Battery terminal.
C. Measure the voltage from terminal 3 to the -Battery terminal.
D. Turn the main disconnect switch to the OFF position.
E. Reconnect the EIC.
   
ECM relay voltage    
Result: The voltage is 24 3 VDC.
The circuit from the ECM to the EIC is OK.
Result: The voltage is not 24 3 VDC.
Repair: Repair the wire between the ECM and the EIC.
Verify that the repair eliminated the problem.
   If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).