5032395 JOHNSON *CAP


5032395 *CAP JOHNSON J10EL4SRC, J10R4SNF, J10R4SR, J10R4STC, J15R4SNF, J15R4SR, J15R4STC, J15RL4SR, J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA CAP
5032395 *CAP JOHNSON
Rating:
43

Buy *CAP 5032395 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 19
 

BRP JOHNSON entire parts catalog list:

J10EL4SRC 2004
J10R4SNF, J10RL4SNF, J10TE4SNF, J10TEL4SNF 2002
J10R4SR, J10RL4SR, J10TBL4SR, J10TE4SR, J10TEL4SR 2004
J10R4STC, J10RBL4STS, J10REL4STS, J10RL4STC, J10TBL4STC, J10TE4STC, J10TEL4STC 2003
J15R4SNF, J15RL4SNF, J15TE4SNF, J15TEL4SNF 2002
J15R4SR, J15TE4SR, J15TEL4SR 2004
J15R4STC, J15RL4STC, J15TE4STC, J15TEL4STC 2003
J15RL4SR 2004
J25PL4SOC, J25TEL4SOC 2005
J25PL4SRS 2004
J30PL4SDR 2006
J30PL4SOC, J30TEL4SOC 2005
J30PL4SRS 2004
J30PL4SUA 2007
J30TEL4SDR 2006
J30TEL4SUA 2007

Information:


Illustration 1 g01239089
Schematic for throttle position sensorTest Step 1. Inspect the Electrical Connectors and the Wiring
Remove the electrical power from the ECM.
Illustration 2 g01141049
J1/P1 ECM connector
Thoroughly inspect the J1/P1 ECM connector and the connector for the throttle position sensor. Inspect the machine connector for damage or corrosion. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 3 g01143213
P1 ECM connector (P1-4) 8 VDC supply (P1-5) Digital return (P1-66) Throttle position
Illustration 4 g01239091
Terminals on the machine connector (Terminal 21) Throttle position (Terminal 23) 8 VDC supply (Terminal 17) Digital return
Illustration 5 g01159881
J403/P403 for the throttle position sensor (A) 8 V supply (B) Digital return (C) Throttle position
Perform a 45 N (10 lb) pull test on each of the wires in the circuit.
Check the allen head screw from each ECM connector for the proper torque. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for the correct torque value.
Check the harness and the wiring for abrasion and for pinch points.Expected Result:All of the connectors, pins and sockets are completely coupled and/or inserted and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The harness and connectors appear to be OK. Proceed to Test Step 2.
Not OK - The connectors and/or wiring are not OK.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Inspect the Throttle Pedal Assembly
Inspect the throttle pedal assembly for components that are loose, bent, missing, or worn.
Slowly depress the pedal and release the pedal.Expected Result:The throttle pedal assembly operates smoothly without excessive drag. The pedal springs back smoothly to the low idle position without assistance.Results:
OK - The throttle pedal assembly functions properly. Proceed to Test Step 3.
Not OK - The throttle pedal assembly is in poor repair.Repair: Repair the throttle pedal assembly or replace the throttle pedal assembly, as required.STOPTest Step 3. Check the Status for "Throttle Position"
Connect the Caterpillar Electronic Technician (ET) to the service tool connector.
Restore the electrical power to the ECM.
Observe the status for "Throttle Position" on Cat ET while you operate the throttle pedal through the entire range of travel.Expected Result:The status is zero percent when the throttle pedal is released. The status progressively increases to 100 percent when the throttle pedal is fully depressed.Results:
OK - The throttle position sensor is working properly.Repair: There may be an intermittent electrical problem with the harness or the connectors. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" if the problem is intermittent.STOP
Not OK - The throttle position that is displayed on Cat ET does not correspond to the movement of the throttle pedal. Proceed to Test Step 4.Test Step 4. Check the Supply Voltage at the Sensor
Disconnect the connector for the throttle position sensor.
Restore the electrical power to the ECM.
Measure the voltage across terminal A (8 V supply) and terminal B (digital return) on the harness side of the connector.
Remove the electrical power from the ECM.Expected Result:The supply voltage measures 8.0 0.4 VDC at the sensor connector.Results:
OK - The correct voltage is measured at the sensor connector. The sensor is receiving the correct supply voltage. Proceed to Test Step 5.
Not OK - The voltage is not correct at the sensor connector. The sensor is not receiving the correct supply voltage. Proceed to Test Step 7.Test Step 5. Check the Signal Frequency and the Duty Cycle at the Sensor
Install a 7X-6370 Adapter Cable As (3-PIN BREAKOUT) at the connector for the throttle position sensor.
Remove the signal wire from terminal C of the connector for the throttle position sensor. Remove the wire from the harness side of the connector.
Restore the electrical power to the ECM.
Measure the frequency and the duty cycle between terminal B (digital return) and terminal C (throttle position) at the 7X-6370 Adapter Cable As (3-PIN BREAKOUT) while you operate the throttle pedal.
Remove the electrical power from the ECM.
Remove the breakout harness. Restore the wires to the original configuration.Expected Result:The frequency is between 150 and 1000 Hz. The duty cycle is between 7 and 95 percent.Results:
OK - The frequency and the duty cycle are within specifications for the entire range of the pedal. The sensor is producing a valid signal. Proceed to Test Step 6.
Not OK - The frequency and the duty cycle are not within specifications.Repair: The sensor is not producing a valid s


Parts cap JOHNSON:

5030633
 
5030633 CAP, Oil fill
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SDM, BJ70PL4SOA, BJ70PL4SRR, BJ70PL4S
5030529
 
5030529 CAP, Relay
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, BJ40PL4SRS, BJ50PL4SRS, BJ60PL4SOA, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SOA, BJ70PL4SRR, BJ70PL4STC, BJ90PL4SDA, BJ90PL4S
5030839
CAP, Screw, stern bracket
5030839 CAP, Screw, stern bracket
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SDM, BJ70PL4SOA, BJ70PL4SRR, BJ70PL4S
5033084
 
5033084 *CAP, MAIN NOZZLE
J10EL4SRC, J10R4SNF, J10R4SR, J10R4STC, J15R4SNF, J15R4SR, J15R4STC, J15RL4SR
5035576
 
5035576 CAP, OIL FILLER
J10EL4SRC, J10R4SR, J15R4SR, J15RL4SR
5035575
 
5035575 CAP, OIL FILLER
J10EL4SRC, J10R4SR, J15R4SR, J15RL4SR
5032396
 
5032396 *CAP
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
5032036
 
5032036 CAP, SPARK PLUG
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
Back to top