5033463 JOHNSON CAP, FUEL TANK


5033463 CAP, FUEL TANK JOHNSON J2R4SDS, J2R4SUC, J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J4R4SUM, J5R4SDA, J5R4SOR, J5R4SRC, J5R4STS, J5R4SUM, J6R4SDC, J6R4SOS, J6R4SUR CAP
5033463 CAP, FUEL TANK JOHNSON
Rating:
58

Buy CAP, FUEL TANK 5033463 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

BRP JOHNSON entire parts catalog list:

J2R4SDS 2006
J2R4SUC 2007
J4R4SDA, J4RL4SDA 2006
J4R4SOR, J4RL4SOR 2005
J4R4SRC, J4RL4SRC 2004
J4R4STS, J4RL4STS 2003
J4R4SUM, J4RL4SUM 2007
J5R4SDA, J5RL4SDA 2006
J5R4SOR, J5RL4SOR 2005
J5R4SRC, J5RL4SRC 2004
J5R4STS, J5RL4STS 2003
J5R4SUM, J5RL4SUM 2007
J6R4SDC, J6RL4SDC 2006
J6R4SOS, J6RL4SOS 2005
J6R4SUR, J6RL4SUR 2007

Information:

Drain
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap.
Open the cooling system drain valve (if equipped). If the cooling system is not equipped with a drain valve, remove the cooling system drain plugs. Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Caterpillar dealer or consult Caterpillar Service Technology Group:Outside Illinois 1-800-542-TOOL
Inside Illinois 1-800-541-TOOL
Canada 1-800-523-TOOL
Flush
Flush the cooling system with clean water in order to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Operation and Maintenance Manual, "Torque Specifications" topic (Maintenance Section) for more information on the proper torques.
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with clean water. Install the cooling system filler cap.
Start and run the engine at low idle until the temperature reaches 49 to 66 °C (120 to 150 °F).
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Operation and Maintenance Manual, "Torque Specifications" topic (Maintenance Section) for more information on the proper torques. Fill
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with Extended Life Coolant (ELC). Refer to the Operation and Maintenance Manual, "Cooling System Specifications" topic (Maintenance Section) for more information on cooling system specifications. Do not install the cooling system filler cap.
Start and run the engine at low idle. Increase the engine rpm to high idle. Run the engine at high idle for one minute in order to purge the air from the cavities of the engine block. Stop the engine.
Check the coolant level. Maintain the coolant level within 13 mm (0.5 inch) below the bottom of the pipe for filling. Maintain the coolant level within 13 mm (0.5 inch) to the proper level on the sight glass (if equipped).
Clean the cooling system filler cap. Inspect the gasket that is on the cooling system filler cap. If the gasket that is on the cooling system filler cap is damaged, discard the old cooling system filler cap and install a new cooling system filler cap. If the gasket that is on the cooling system filler cap is not damaged, use a 9S-8140 Pressurizing Pump in order to pressure test the cooling system filler cap. The correct pressure for the cooling system filler cap is stamped on the face of the cooling system filler cap. If the cooling system filler cap does not retain the correct pressure, install a new cooling system filler cap.
Start the engine. Inspect the cooling system for leaks and for proper operating temperature.


Parts cap JOHNSON:

5031254
 
5031254 CAP
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J4R4SUM, J50PL4SNF, J50PL4STC, J5R4SDA, J5R4SOR, J5R4SRC, J5R4STS, J5R4SUM, J6R4SDC, J6R4SOS, J6R4SUR
5034196
 
5034196 CAP, FUEL CONNECTOR PLUG
J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J4R4SUM, J5R4SDA, J5R4SOR, J5R4SRC, J5R4STS, J5R4SUM, J6R4SDC, J6R4SOS, J6R4SUR
5033497
 
5033497 CAP, SPARK PLUG
J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J4R4SUM, J5R4SDA, J5R4SOR, J5R4SRC, J5R4STS, J5R4SUM, J6R4SDC, J6R4SOS, J6R4SUR
5033498
 
5033498 CAP, TRANSOM BOLT
J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J4R4SUM, J5R4SDA, J5R4SOR, J5R4SRC, J5R4STS, J5R4SUM, J6R4SDC, J6R4SOS, J6R4SUR
5034258
 
5034258 ***CAP, Lighting receptac
J10EL4SOR, J10RL4SDM, J15EL4SOS, J15RL4SDM, J4R4SOR, J5R4SOR, J6R4SOS
5037304
 
5037304 CAP, Oil filler
J2R4SDS, J2R4SUC
5037379
 
5037379 CAP, SPARK PLUG
J2R4SDS, J2R4SUC
5037257
 
5037257 CAP, CLAMP SCREW
J2R4SDS, J2R4SUC
Back to top