0436793 JOHNSON CARB. ASSY., Stbd., 150JL


0436793 CARB. ASSY., Stbd., 150JL JOHNSON BJ150ELEDB, BJ175EXEDB, J150ELARA, J150ELEOM, J175EXARC, J175EXEOM CARB
0436793 CARB. ASSY., Stbd., 150JL JOHNSON
Rating:
48

Buy CARB. ASSY., Stbd., 150JL 0436793 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 43679
 

BRP JOHNSON entire parts catalog list:

BJ150ELEDB, BJ150EXEDB, BJ150GLEDB, BJ150NXEDB, J150ELEDB, J150EXEDB, J150GLEDB, J150JLEDB, J150NXEDB, J150SLEDB, SJ150ELEDB 1996
BJ175EXEDB, BJ175GLEDB, BJ175NXEDB, J175EXEDB, J175GLEDB, J175NXEDB, J175SLEDB 1996
J150ELARA, J150ELARV, J150ELERA, J150ELERV, J150EXARC, J150EXARV, J150EXERA, J150EXERV, J150GLERA, J150GLERV, J150JLERA, J150JLERV, J150NXARC, J150NXARV, J150NXERA, J150NXERV 1994
J150ELEOM, J150EXEOM, J150GLEOM, J150JLEOM, J150NXEOM, J150SLEOM, VJ150HLEOS 1995
J175EXARC, J175EXARV, J175EXERA, J175EXERV, J175GLERA, J175NXARC, J175NXARV, J175NXERA, J175NXERV, J175SLERA 1994
J175EXEOM, J175GLEOM, J175NXEOM, J175SLEOM 1995

Information:

1. Remove the plug from location (1). Install tool (A) in the hole with the square end down. Move the governor control to the "ON" position until the rack stops against tool (A). The racks are now in center (zero) position. 2. Disconnect lines (2) from the fuel injection pumps. Remove washers (3). Put caps on all fuel openings.3. Remove bushing (4) with tool (B).
When injection pumps, spacers and lifters are removed from the injection pump housing, keep the parts of each pump together so they can be installed back in their original location.
4. Remove fuel injection pump with tool (C).
Be careful when the injection pumps are disassembled. Do not cause damage to the surface on the plunger. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump in the barrel of another pump. If one part has wear install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
5. Disassemble the fuel injection pump. Remove ring (6). Make a separation of bonnet (5) from the plunger and barrel assembly (7).
Do not remove the gear from the plunger. The gear and plunger are assembled and adjusted at the factory.
6. Remove the plunger and gear segment, washer and spring from the barrel.7. Remove the ring, spring, collar and valve from the barrel. 8. Remove spacer (8) from the pump bore.Install Fuel Injection Pumps
Make sure the fuel racks are in the center (zero) position before the fuel injection pumps are installed. 1. Put plunger (10), washer (5) and spring (9) in position on barrel (4). Put check valve assembly (7), spring (3) and collar (8) in position in bonnet (6). Connect bonnet (6) and barrel (4) together with ring (2). Keep seal (1) with bonnet for use at installation. 2. Put spacer (13) into position in the pump housing bore. Make sure the correct spacer is with each pump.3. Put the space in gear segment (11) in alignment with the groove in barrel (4). 4. Put the injection pump straight down into the housing bore so the space in gear segment (11) is in alignment with pin (12) and the groove in barrel (4) is in alignment with dowel (14). Use tool (C) to install the pump. 5. Install seal (1) and bushing (15) in the pump housing bore. if the pump is in the correct position, bushing (15) will turn into the threads of the pump housing with the fingers until it is even with the housing. Tighten bushing (15) to a torque of 205 14 N m (150 10 lb ft) with tool (B).6. Install washers (16).7. Connect the fuel lines to the injection pumps and tighten fuel line nuts to a torque of 40 7 N m (30 5 lb ft) with tool (D).8. Check for correct installation of the injection pumps with the engine stopped. See Installation Of Injection Pump in Testing And Adjusting.
If one or more of the injection pumps have been installed wrong, damage to the engine is possible if cautions are not taken when the engine is first started. Make preparation to close off the air intake to stop the engine if necessary.
9. Remove the timing pin [tool (A)] and install the plug in the injection pump housing.


Parts carb JOHNSON:

0435082
 
0435082 CARB. BODY AY., 150 XP, GT, 175
J150ELAIS, J150ELANC, J150ELARA, J150ELATG, J175EXARC, J175EXATG, J175EXEIS, J175EXENC
0434639
 
0434639 CARB. ASSY., Port, 150 XP, GT
J150ELAIS, J150ELANC, J150ELARA, J150ELATG, J175EXARC, J175EXATG, J175EXEIS, J175EXENC
0435295
 
0435295 CARB, ASSY., Stbd., 175
J150ELANC, J150ELARA, J150ELATG, J175EXARC, J175EXATG, J175EXENC
0435296
 
0435296 CARB, ASSY., Port, 175
J150ELANC, J150ELARA, J150ELATG, J175EXARC, J175EXATG, J175EXENC
0435528
 
0435528 CARB ASSY., Stbd. 150
J150ELANC, J150ELARA, J150ELATG, J150WTLETG, J175EXARC, J175EXATG, J175EXENC
0436016
 
0436016 CARB. ASSY., Stbd., 150JL
J150ELARA, J175EXARC
0436017
 
0436017 CARB. ASSY., Port, 150JL
J150ELARA, J175EXARC
0436830
Back to top