0385128 CARBURETOR ASSY., Lower JOHNSON
65ES72S
CARBURETOR
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$245.90
07-09-2017
4.40[1.80] pounds
Lyndall Ra: Lyndall Racing Brake
Lyndall Racing Brakes 038-5128 TT Tracker Rear Carrier - Black
Quick application guide (for exact rotor dimensions for your model refer to your OEM parts guide):||00-07 Touring models require 11.5in. rotors front and back||08-13 Touring models require 11.8in. rotors front and back||08-Up Dynas with laced wheels require 11.8in. rotors front and 11.5in. rear rotors||Create your own rotors to match your Lyndall wheels. Choose your center carrier design and finish then choose the friction ring that fits your application in silver or black high carbon steel in crown cut or smooth. Layndalls patented lug drive design allows for easy assembly and unmatched braking performance. Carriers fit 2000 and later wheels with hub mounted rotors, for perimeter style rotors (used on 14-Up Touring models and 06-Up Dynas with cast wheels) see the Lyndall rotors in the brake s
Quick application guide (for exact rotor dimensions for your model refer to your OEM parts guide):||00-07 Touring models require 11.5in. rotors front and back||08-13 Touring models require 11.8in. rotors front and back||08-Up Dynas with laced wheels require 11.8in. rotors front and 11.5in. rear rotors||Create your own rotors to match your Lyndall wheels. Choose your center carrier design and finish then choose the friction ring that fits your application in silver or black high carbon steel in crown cut or smooth. Layndalls patented lug drive design allows for easy assembly and unmatched braking performance. Carriers fit 2000 and later wheels with hub mounted rotors, for perimeter style rotors (used on 14-Up Touring models and 06-Up Dynas with cast wheels) see the Lyndall rotors in the brake s
$29.10
11-06-2023
0.1873[0.08] Pounds
-: -
O'Neal 0385-128 Jump Gloves with Crank Graphic (Black/Multicolor, Size 8)
Silicone printing for a better grip. Long lasting and flexible materials for the perfect fit || Super lightweight design with bold non-fade graphics || Seamless rollover fingertips. Synthetic leather palm with double layer thumb reinforcement || Hook and loop adjustable wrist closure || Available in: Crank Black/Multi, Mayhem Blocker Black/White, Mayhem Blocker Black/Hi-Viz, H/W Jag Black/Red, H/W Skim Blue/Red, H/W Skim Neon/Teal
Silicone printing for a better grip. Long lasting and flexible materials for the perfect fit || Super lightweight design with bold non-fade graphics || Seamless rollover fingertips. Synthetic leather palm with double layer thumb reinforcement || Hook and loop adjustable wrist closure || Available in: Crank Black/Multi, Mayhem Blocker Black/White, Mayhem Blocker Black/Hi-Viz, H/W Jag Black/Red, H/W Skim Blue/Red, H/W Skim Neon/Teal
Number on catalog scheme: 38512
Compatible models:
65ES72S
JOHNSON
BRP JOHNSON entire parts catalog list:
Information:
Table 1
Diagnostic Codes Table
Code Conditions which Generate this Code System Response
2417-5 Ether Injection Control Solenoid : Current Below Normal The Electronic Control Module (ECM) detects low current in the circuit. The code is latched. The code is logged.
Ether injection is disabled.
2417-6 Ether Injection Control Solenoid : Current Above Normal The ECM detects excessive current flow in the circuit. The ether injection system improves cold weather starting of the engine. The ECM controls the ether injection system. The ether injection system is enabled when all of the following conditions occur:
The configuration parameter is enabled or the configuration parameter is set to continuous flow.
The intake manifold air temperature is less than 0 °C (32 °F) or the engine coolant temperature is less than 0 °C (32 °F).
Engine speed is greater than 0 rpm and less than 50 rpm below the low idle speed.
No diagnostic codes are active for both the engine coolant temperature sensor and for the intake manifold air temperature sensor.
Illustration 1 g02099717
Schematic of the ether injection system
Illustration 2 g02099721
P1 terminals for the ether injection system
(P1-10) Starting aid solenoid
(P1-18) Return for the starting aid solenoid
Illustration 3 g01155187
Terminal locations at the harness connector for the ether solenoid
(1) Starting aid solenoid
(2) Return for the starting aid solenoid
Table 2
Troubleshooting Test Steps Values Results
1. Check the Harness Connectors
A. Verify that the keyswitch is in the OFF position.
B. Disconnect the harness connector for the ether solenoid.
C. Check the harness connector for debris and for corrosion.
Connectors
Result: The harness connector was not free of debris and/or not free of corrosion.
Repair: Perform the following procedure:
1. Clean the harness connector.
2. Reconnect the harness connector. Verify that the connection is secure.
3. Verify that the problem is resolved.
If the problem is not resolved, proceed to Test Step 2.
Result: The harness connector was free of debris and free of corrosion.
Proceed to Test Step 2.
2. Create an Open at the Harness Connector for the Ether Injection Solenoid
Note: The ether canister must be removed prior to performing this procedure.
A. If necessary, disconnect the harness connector from the ether solenoid.
B. Turn the keyswitch to the ON position.
C. A test on Caterpillar Electronic Technician (ET) allows the technician to activate the ether system. The test can be activated by selecting the "Diagnostic Overrides" screen on Cat ET.
D. Activate the ether injection system. The system will activate for 10 seconds.
E. Measure the voltage across terminal 1 and terminal 2 of the harness for the ether injection solenoid.
F. Turn the keyswitch to the OFF position.
Voltage
Result: The voltage measurement is 0 VDC after activating the ether injection system.
Repair: There is a problem in the harness. Repair the harness or replace the harness.
Verify that the problem is resolved.
STOP
Result: The voltage measurement is equal to battery voltage after activating the ether injection system.
Repair: There is a problem in the solenoid. Replace the solenoid.
Verify that the problem is resolved.
STOP
Test Step 1. The procedure corrected the issue. Return to service.Results:
The procedure did not correct the issue. - Repair: Contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).STOP
Parts carburetor JOHNSON:
0385129
0385130