0384256 JOHNSON CHOKE SHAFT AND PIN


0384256 CHOKE SHAFT AND PIN JOHNSON 100ESL71A, 100ESL72R, 115EL77S, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 85EL76D, 85EL77S, 85ESL70B, 85ESL71A, 85ESL73M, 85ESL74B, 85ESL75E, 85TXLR77S CHOKE
0384256 CHOKE SHAFT AND PIN JOHNSON
Rating:
88

Buy CHOKE SHAFT AND PIN 0384256 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 9
 

BRP JOHNSON entire parts catalog list:

100ESL71A, 100ESL71C 1971
100ESL72R 1972
115EL77S, 115ETL77 1977
115ESL70D 1970
115ESL73M 1973
115ESL74B, 115ETL74B 1974
115ESL75E, 115ETL75E 1975
115TXL77S 1977
125ESL71C 1971
125ESL72R 1972
135ESL73M 1973
135ESL74B, 135ETL74B 1974
135ESL75E, 135ETL75E 1975
140ML77S, 140TL77S, 140TXL77S 1977
85EL76D, 85EL76G, 85ETLR76D, 85ETLR76G 1976
85EL77S, 85ETLR77S 1977
85ESL70B, 85ESL70D 1970
85ESL71A, 85ESL71H 1971
85ESL73M 1973
85ESL74B 1974
85ESL75E 1975
85TXLR77S 1977

Information:

START BY:a. remove turbocharger 1. Install the turbocharger on tool group (A). Put alignment marks on the three housings of the turbocharger for correct installation and alignment at assembly.2. Loosen clamp (2), and remove housing (1) and clamp (2). 3. Loosen clamp (3), and remove housing (4) and clamp (3). 4. Put cartridge assembly (5) in position on tooling (B).
Do not put a side force on the shaft when the nut is loosened.
5. Use tooling (C) to remove the nut from the shaft. 6. Use a press to push the shaft assembly out of the cartridge assembly.7. Remove wheel (6) from the cartridge. 8. Remove shroud (8) and the seal ring from shaft assembly (7). 9. Use tooling (D) to remove snap ring (9) from the cartridge. 10. Use screwdrivers (11) to lift up on insert assembly (10). 11. Remove sleeve (12) from the insert.12. Remove the two seal rings from the sleeve.13. Remove O-ring seal (13) from the insert. 14. Remove deflector (14) from the cartridge. 15. Remove spacer (15) from the cartridge. 16. Remove bearing (16) from the cartridge. 17. Remove sleeve (17) and O-ring (18). 18. Use tooling (E) to remove snap ring (19) from the cartridge. 19. Remove bearing (20) and the other snap ring. 20. Turn the cartridge housing over.21. Use tooling (E) to remove snap ring (21) from the cartridge.22. Remove the bearing and snap ring.Assemble Turbocharger (Schwitzer F301)
1. Make sure that all of the oil passages in the cartridge housing assembly are clean and free of dirt and foreign material. Put clean oil on all the parts of the cartridge assembly.2. Install snap ring (1) in cartridge housing (2) with tooling (A).3. Install the bearing and the other snap ring.4. Turn the housing over. 5. Install snap ring (3) with tooling (A).6. Install the bearing and other snap ring. 7. Put ring (4) and sleeve (5) in position in the cartridge. 8. Install bearing (7) with the grooved side up. Make an alignment of the dowels in the housing with the holes in the bearing.9. Put spacer (6) in position on the bearing. 10. Put deflector (8) in position as shown. 11. Put seal rings (9) in position on sleeve (10).12. Install the sleeve in insert (11).13. Install O-ring seal (12) on the insert. 14. Put insert assembly (13) in position in the cartridge. 15. Use tooling (C) to install snap ring (14) in the cartridge housing. Put 6V2055 High Vacuum Grease in the groove for the seal ring at assembly to one half or more of the depth of the groove all the way around shaft (16).16. Install the seal ring on shaft assembly (16).17. Put the shaft assembly in position on tooling (B).18. Put shroud (15) in position on the shaft. 19. Put cartridge assembly (17) in position on the shaft assembly. 20. Put compressor wheel (18) in position on the shaft. 21. Put clean oil on the threads on the shaft and the top surface of the wheel that makes contact with the nut.
Do not put a side force on the shaft when the nut that holds the compressor wheel in position is tightened.
22. Install the nut that holds the compressor wheel in place. Tighten the nut to a torque of 25 1 N m (18 1 lb.ft.). 23. Put the cartridge assembly in position in a vise as shown. Make sure soft jaws are used. Install tooling (E) on the cartridge assembly to check the end play. End play must be 0.114 0.038 mm (.0045 .0015 in.). 24. Put housing (20) in position on tooling (D).25. Put cartridge assembly (19) in position in housing (20), and install clamp (22). Tighten the clamp to a torque of 13.6 N m (120 lb.in.).26. Install housing (21) on the cartridge, and install clamp (23). Tighten the clamp to a torque of 13.6 N m (120 lb.in.).END BY:a. install turbocharger


Parts choke JOHNSON:

0383639
 
0383639 CHOKE KNOB AND ROD ASSEMBLY
100ESL71A, 115ESL69E, 115ESL70D, 125ESL71C, 85ESL69E, 85ESL70B, 85ESL71A
0316092
 
0316092 CHOKE VALVE
100ESL71A, 100ESL72R, 115EL77S, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 175TL77S, 200TL76S, 200TL77C, 85EL76D, 85EL77S, 85ESL70B, 85ESL71A, 85ESL72R, 85ESL73M, 85ESL74B,
0384255
 
0384255 CHOKE SHAFT AND LEVER
100ESL71A, 100ESL72R, 115EL77S, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 85EL76D, 85EL77S, 85ESL70B, 85ESL71A, 85ESL72R, 85ESL73M, 85ESL74B, 85ESL75E, 85TXLR77S
0385372
 
0385372 CHOKE KNOB ASSY
100ESL72R, 115ESL73M, 115ESL74B, 125ESL72R, 135ESL73M, 135ESL74B, 85ESL72R, 85ESL73M, 85ESL74B
0387838
 
0387838 CHOKE SHAFT, 115 HP only
115EL77S, 115TXL77S, 140ML77S, 85EL77S, 85TXLR77S
Back to top