0388053 JOHNSON CLAMP SCR AND HAND ASSY

Illustration 1 g02015056
Cylinder and valve location (A) Exhaust (B) Inlet (C) Flywheel
Table 1
Crankshaft Positions for Fuel Injector and Valve Lash Setting    
C280-6
Engine     Check and Adjust with No. 1 Piston on the Following Stroke: (1)    
Top Center Compression Stroke Top Center Exhaust Stroke    
SAE Standard Rotation Engines (2)    
Inlet
Valves     1-2-4     3-5-6    
Exhaust Valves     1-3-5     2-4-6    
Fuel
Injectors     3-5-6     1-2-4    
Firing
Order     1-5-3-6-2-4    
SAE Opposite Rotation Engines (3)    
Inlet
Valves     1-3-5     2-4-6    
Exhaust Valves     1-2-4     3-5-6    
Fuel
Injectors     2-4-6     1-3-5    
Firing
Order     1-4-2-6-3-5    
( 1 ) Put the No. 1 piston at the top center position and identify the correct stroke. Refer to Testing and Adjusting, "Finding the Top Center Position for the No. 1 Piston". After the top center position for a particular stroke is found and the adjustments are made for the correct cylinders, remove the timing pin. Turn the flywheel for 360 degrees in the direction of normal engine rotation. The rotation will put the No. 1 piston at the top center position on the other stroke. Install the timing pin in the crankshaft and complete the adjustments for the cylinders that remain.
( 2 ) SAE Standard Rotation Engines turn in the counterclockwise direction when the engines are viewed from the flywheel end.
( 3 ) SAE Opposite Rotation Engines turn in the clockwise direction when the engines are viewed from the flywheel end.8-Cylinder Engine
Illustration 2 g02015057
Cylinder and valve location (A) Exhaust (B) Inlet (C) Flywheel
Table 2
Crankshaft Positions for Fuel Injector and Valve Lash Setting    
C280-8
Engine     Check and Adjust with No. 1 Piston on the Following Stroke: (1)    
Top Center Compression Stroke Top Center Exhaust Stroke    
SAE Standard Rotation Engines (2)    
Inlet
Valves     1-4-6-7     2-3-5-8    
Exhaust Valves     1-2-4-6     3-5-7-8    
Fuel
Injectors     2-3-5-8     1-4-6-7    
Firing
Order     1-6-2-5-8-3-7-4    
SAE Opposite Rotation Engines (3)    
Inlet
Valves     1-2-4-6     3-5-7-8    
Exhaust Valves     1-4-6-7     2-3-5-8    
Fuel
Injectors     3-5-7-8     1-2-4-6    
Firing
Order     1-4-7-3-8-5-2-6    
( 1 ) Put the No. 1 piston at the top center position and identify the correct stroke. Refer to Testing and Adjusting, "Finding the Top Center Position for the No. 1 Piston". After the top center position for a particular stroke is found and the adjustments are made for the correct cylinders, remove the timing pin. Turn the flywheel for 360 degrees in the direction of normal engine rotation. The rotation will put the No. 1 piston at the top center position on the other stroke. Install the timing pin in the crankshaft and complete the adjustments for the cylinders that remain.
( 2 ) SAE Standard Rotation Engines turn in the counterclockwise direction when the engines are viewed from the flywheel end.
( 3 ) SAE Opposite Rotation Engines turn in the clockwise direction when the engines are viewed from the flywheel end.12-Cylinder Engine
Illustration 3 g01192815
Cylinder and valve location (A) Exhaust (B) Inlet (C) Flywheel