0391428 JOHNSON CLAMP SCR. & HAND. ASSY.


0391428 CLAMP SCR. & HAND. ASSY. JOHNSON J2RCIB, J2RCNE, J2RCOC, J2RCRS, J2RCTD, J4BRCIC, J4BRHCNR, J4BRHCOB, J4BRHCRM, J4BRHCTA, J4WCIC, J4WCNR, JCO-CDR, JCO-CUA CLAMP
0391428 CLAMP SCR. & HAND. ASSY. JOHNSON
Rating:
58

Buy CLAMP SCR. & HAND. ASSY. 0391428 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 20
 

BRP JOHNSON entire parts catalog list:

J2RCIB 1981
J2RCNE 1982
J2RCOC 1985
J2RCRS 1984
J2RCTD 1983
J4BRCIC, J4BRLCIC 1981
J4BRHCNR, J4BRHLCNR 1982
J4BRHCOB, J4BRHLCOB 1985
J4BRHCRM, J4BRHLCRM 1984
J4BRHCTA, J4BRHLCTA 1983
J4WCIC 1981
J4WCNR 1982
JCO-CDR 1986
JCO-CUA 1987

Information:


Illustration 1 g01303631
Schematic for the analog sensor
Test Step 1. INSPECT THE ELECTRICAL CONNECTORS AND WIRING
Remove the electrical power from the engine. Note: For the following steps, refer to Troubleshooting, "Electrical Connectors - Inspect".
Thoroughly inspect each of the following connectors:
J1/P1 connectors
J7/P7 connectors
Check the torque of the allen head screws for the ECM connectors.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit for the analog sensors.
Check the harness and wiring for abrasion and for pinch points from the analog sensors to the master ECM. Expected Result:All connectors, pins, and sockets are connected properly. The connectors and the wiring do not have corrosion, abrasion, or pinch points.Results:
OK - All connectors, pins, and sockets are connected properly. The connectors and the wiring do not have corrosion, abrasion, or pinch points. The components are in good condition with proper connections. If you are troubleshooting a -3 code, proceed to Test Step 3. If you are troubleshooting a -4 code, proceed to Test Step 2.
Not OK - At least one of the connectors, pins, and/or sockets are not connected properly. At least one of the connectors and/or the wiring has corrosion, abrasion, or pinch points.Repair: Perform the necessary repairs and/or replace parts, if necessary.STOPTest Step 2. CREATE AN OPEN CIRCUIT FOR THE SENSOR
Disconnect the sensor that has the "voltage below normal" diagnostic code.
Observe the "Active Diagnostic" screen on Cat ET. Allow a minimum of 30 seconds for any codes to activate. Look for an active -3 diagnostic code. Expected Result:There is an active -3 diagnostic code for the disconnected sensor.Results:
Yes - Before the suspect sensor was disconnected, there was an active -4 diagnostic code for the sensor. After the suspect sensor was disconnected, there was an active -3 diagnostic code for the sensor.Repair: Reconnect the sensor. If the active -4 diagnostic code recurs, replace the original sensor.Verify that the code does not activate when the new sensor is installed. Clear the logged codes from the master ECM.STOP
No - Before the suspect sensor was disconnected, there was an active -4 diagnostic code for the sensor. After the suspect sensor was disconnected, the active -4 diagnostic code remained. Proceed to Test Step 3.Test Step 3. CHECK THE PULL-UP VOLTAGE AT THE SENSOR
Verify that the suspect sensor's connector is disconnected from the engine harness.
Illustration 2 g01303636
Harness connectors for the sensor
(1) Signal
(2) Return
At the harness connector for the suspect sensor, measure the voltage between terminals (1) and (2). Expected Result:The voltage is between 6.0 VDC and 7.0 VDC.Results:
OK - The voltage between the signal terminal and the return terminal is between 6.0 VDC and 7.0 VDC. The pull-up voltage that is created by the master ECM is present at the sensor connector. The signal wire and the return wire for the suspect sensor appear to be OK. Proceed to Test Step 5.
Not OK - The voltage between the signal terminal and the return terminal is not between 6.0 VDC and 7.0 VDC. The pull-up voltage that is created by the master ECM is not present at the sensor connector. Proceed to Test Step 4.Test Step 4. CHECK THE PULL-UP VOLTAGE AT THE MASTER ECM
Use a 151-6320 Wire Removal Tool to remove the signal wire for the suspect sensor from the P1 connector.
Use a jumper wire with


Parts clamp JOHNSON:

0510190
 
0510190 CLAMP
1R69C, 1R70R, 20R73A, 25E73A, 25E74M, 25E75B, 25E76E, 2R71A, 2R72M, 2R73B, 2R74E, 2R75D, 2R76S, 2R77C, 2R78R, 2R79A, 33E69A, 33E69A, 33E70M, 33E70M, 40E69R, 40E70A, 40E71B, 40E72E, 40E73D, 40ES69R, 40ES70A, 40R69R, 40R70A, 9R69S, 9R70A, 9R71R, 9R72M,
0303596
 
0303596 CLAMP,Horse
100ESL71A, 100ESL72R, 100ML79S, 10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78
0553166
 
0553166 CLAMP,Bulb to nipple
100ESL71A, 100ESL72R, 100ML79S, 10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78
0315224
 
0315224 CLAMP, Stern bracket 5" EXTENSION KIT
1R69C, 1R70R, 2R71A, 2R72M, 2R73B, 2R74E, 2R75D, 2R76S, 2R77C, 2R78R, 2R79A, J2RCIB, J2RCNE, J2RCOC, J2RCRS, J2RCSM, J2RCTD, JCO-CCM, JCO-CDR, JCO-CEB, JCO-CUA, JCO-ESE
0320107
 
0320107 CLAMP STRAP, Hose
100ML79S, 10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 115EL77S, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 15E74G, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, 175TL77
0312387
 
0312387 CLAMP, Fuel tank
2R75D, 2R76S, 2R77C, 2R78R, 2R79A, J2RCIB, J2RCNE, J2RCSM, J2RCTD
0388346
CLAMP SCR.&HAND.ASSY.
0388346 CLAMP SCR.&HAND.ASSY.
2R77C, 2R78R, 2R79A, 4R77B, 4R78E, 4R79D, 6R77M, 6R78B, 6R79E, J2RCNE, J2RCOC, J2RCRS, J2RCSM, J2RCTD, J4BRHCNR, J4BRHCOB, J4BRHCRM, J4BRHCTA, J4RLCSS, J4WCNR, JCO-CDR, JCO-CUA
0322654
CLAMP,Hose to carb.
0322654 CLAMP,Hose to carb.
2R77C, 2R78R, 2R79A, BJ115ELEDR, BJ115ELEUA, BJ115GLECM, BJ115PLEEM, BJ115PLSSB, BJ130PLEED, BJ130PLSSS, BJ130TLECE, BJ130TLEDM, BJ130TLEUB, BJ250CXECB, BJ250CXEDA, BJ250CXEUM, BJ3REDS, BJ40EECR, BJ40EEDS, BJ40EEEA, BJ40EEUC, BJ40ELSIF, BJ40ELSSM, BJ
Back to top