5030590 JOHNSON CLAMP, Leads

Table 1
Specifications for 346-4197 Crankshaft Gp    
Callout     Part Number     Part Name     Specification Description    
-     338-1402     Crankshaft Gear     Maximum permissible temperature of the gear for installation on the crankshaft is 180 °C (356 °F).    
-     355-8526     Crankshaft     The end play of a new crankshaft is
0.1 to 0.41 mm (0.00394 to 0.01614 inch).    
7     363-0559     Thrust Washer     Standard thickness of thrust washer is
2.69 to 2.75 mm (0.10591 to 0.10827 inch).    
-     -     Journal 1     Mounting    
-     -     Journal 2     Run out of the journal is
0.08 mm (0.0031 inch).    
-     -     Journal 3     Run out of the journal is
0.15 mm (0.0059 inch).    
-     -     Journal 4     Run out of the journal is
0.08 mm (0.0031 inch).    
-     -     Journal 5     Mounting    Inspect the crankshaft for wear or for damage. For more information regarding the servicing of the crankshaft, contact the Dealer Solution Network (DSN).Removal Procedure
Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     1U-8221     Lifting Sling     2    
B     -     5mm Allen Socket     1    Start By:
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump" for the correct procedure.
Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front)" for the correct procedure.
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal" for the correct procedure.
Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod" for the correct procedure.
If necessary, remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head" for the correct procedure.
If necessary, remove the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The engine should be mounted on a suitable stand and placed in the inverted position.
If the cylinder head, the pistons and the connecting rods have not been removed already, remove the connecting rod bearings. Refer to Disassembly and Assembly, "Connecting Rod Bearings" for the correct procedure.
Illustration 1 g02441836
Use Tooling (B) in order to remove allen head screws (1) . Remove bridge piece (2) .
Ensure that the main bearing caps are marked for the location and orientation.
Illustration 2 g02441837
Illustration 3 g02441838
Remove bolts (3) from main bearing caps (2) . Remove main bearing caps (2) from the cylinder block.
Take care not to displace dowels (6) .
Remove lower main bearing shells (5) from main bearing caps (4) . Keep the lower main bearing shells with the respective main bearing caps.Note: The lower main bearing shells are plain bearings that have no oil holes.
Illustration 4 g02441839
Attach Tooling (A) and a suitable lifting device to crankshaft (7) . Lift crankshaft (7) out of the cylinder block. The weight of the crankshaft is approximately 39 kg (86 lb).Note: Do not damage any of the finished surfaces on the crankshaft. When the crankshaft is removed from the engine, the crankshaft must be supported on a suitable stand in order to prevent damage to the crankshaft timing ring.
Illustration 5 g02441840
Remove upper main bearing shells (8) from the cylinder block. Keep the upper main bearing shells with the respective main bearing caps.Note: The upper main bearing shells have a groove and two oil holes.
Remove thrust washers (7) .
If necessary, remove the crankshaft timing ring. Refer to Disassem