0395861 JOHNSON CONNECTING ROD ASSY.

Table 1
Diagnostic Codes Table
J1939 Code and Description Conditions which Generate this Code System Response
5419-2 Engine Throttle Actuator #1 : Erratic, Intermittent, or Incorrect The throttle actuator has reported that a calibration has been attempted and the calibration has failed. The code is logged.
The amber warning lamp is activated.
5419-7 Engine Throttle Actuator #1 : Not Responding Properly The throttle actuator has reported that there is a mismatch between the requested throttle position and the actual position of the throttle.
5419-12 Engine Throttle Actuator #1 : Failure The throttle actuator has reported an internal failure.
5419-13 Engine Throttle Actuator #1 : Calibration Required The throttle actuator has reported that a calibration attempt has failed. The actuator cannot find the end stop. The throttle actuator works with the Electronic Control Module (ECM) to ensure the correct throttle position during all engine operating conditions.The ECM controls the position of the throttle from a fully closed position to a fully opened position.CommunicationsThe ECM and the throttle actuator communicate via the CAN data link. The ECM sends a command signal to the actuator. The actuator sends the following information to the ECM: desired actuator position, actual actuator position and internal fault diagnosis.If the ECM cannot communicate with the actuator, the ECM activates a 51-9 diagnostic code. This problem may be a problem with the power supply to the actuator. This code may be generated for an intermittent problem. After checking the power circuit for the actuator, refer to Troubleshooting, "CAN Data Link - Test" for information that is related to troubleshooting the data link circuitry.Self-diagnostic FunctionIf an internal fault is detected by the actuator, the condition is communicated via the CAN data link. The ECM activates a 5419-12 diagnostic code. The most likely cause of a 5419-12 diagnostic code is an electrical problem or a mechanical problem.Calibration Failure MessagesA calibration is initiated when the power to the actuator is cycled. The power must be removed from the engine in order to power down the actuator.If a calibration attempt fails at any time, the ECM activates a 5419-2 diagnostic code. If an attempt to calibrate the actuator fails, the actuator will attempt the calibration several times. The 5419-2 code will remain active during this time. If the actuator determines that a calibration is not possible, the 5419-2 code will be deactivated and the ECM will generate a 5419-13 diagnostic code. If the actuator forces a calibration attempt and the engine is running, a 5419-2 code will be generated. The code will remain active until the engine is shut down and the code will become logged. The ECM will then generate a 5419-13 diagnostic code.The most likely cause of a 5419-2 code is an intermittent electrical problem in the circuit for the power supply to the actuator. The most likely cause of repeated unsuccessful calibrations is a dirty valve assembly or a malfunctioning valve assembly.
Illustration 1 g02633858
Schematic for the circuit of the throttle actuator
Test Step 1. Inspect the Electrical Connectors and the Wiring
Remove the electrical power from the engine.
Illustration 2 g02349903
Location of the connector at the throttle actuator (top rear engine view)
(1) Connector for the throttle actuator
Illustration 3 g02630436
Locations of the connectors at the ECM panel that are for the throttle actuator (right side engine view)
(2) J1/P1 ECM connectors
(3) Power strip in the ECM control box
(4) Engine harness components for incendive components
Illustration 4 g02631156
Terminal locations at the J1/P1 ECM connectors for the battery power
(P1-48) +Battery
(P1-52) +Battery
(P1-53) +Battery
(P1-55) +Battery
(P1-57) +Battery
(P1-61) −Battery
(P1-63) −Battery
(P1-65) −Battery
(P1-67) −Battery
(P1-69) −Battery
Illustration 5 g02698400
Terminal locations at the engine harness connector for the incendive components
(Terminal A) +Battery
(Terminal C) −Battery
(Terminal D) +Battery
(Terminal E) −Battery
(Terminal H) −Battery
(Terminal F) −Battery
Illustration 6 g02698402
Locations of the connections at the harness connector for the throttle actuator
(Terminal 1) +Battery
(Terminal 2) −Battery
(Terminal 3) PWM return
(Terminal 5) −Battery
(Terminal 8) +Battery
(Terminal 12) −Battery
Illustration 7 g02631157
Terminal locations at the connector for the breaker panel that are for the electrical power supply
(Terminal A) +Battery
(Terminal B) −Battery
Illustration 8 g02628962
Locations of the circuit connections at the power strip that is inside the ECM control panel
(F1) Fuse for power to the ECM and fuel actuator (15 amp)
(Terminals 1-