0176295 JOHNSON CONNECTOR, 2-socket

Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7370 Belt Tension Test Tool 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from contact with refrigerant.This system is under pressure at all times, engine running or not. Heat should never be applied to a charged system. Contact with refrigerant can cause frost bite. Keep face and hands away to help prevent injury.Protective goggles must always be worn when refrigerant lines are opened, even if the gauges indicate the system is empty of refrigerant.Always use precaution when a fitting is removed. Slowly loosen the fitting. If the system is still under pressure, release it slowly in a well ventilated area.Personal injury or death can result from inhaling refrigerant through a lit cigarette.Inhaling air conditioner refrigerant gas through a lit cigarette or other smoking method or inhaling fumes released from a flame contacting air conditioner refrigerant gas, can cause bodily harm or death.Do not smoke when servicing air conditioners or wherever refrigerant gas may be present.Before any checks of the air conditioning and heating system are made, move the machine to a smooth horizontal surface. Lower all implements to the ground. Make sure the transmission is in NEUTRAL or PARK and that the parking brake is engaged. Keep all other personnel either away from the machine or where they can be seen.
Install caps and plugs on all openings in order to prevent dirt or debris from entering the system. Cleanliness is an important factor. Before the removal procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal components.
Before any service work is performed on the air conditioning system consult the following reference. Refer to Disassembly and Assembly, Air Conditioning and Heating, SENR5664, "Machine Preparation for Disassembly and Assembly".
Recover the refrigerant from the air conditioning system. Refer to Air Conditioning and Heating Testing and Adjusting, SENR5664, "Refrigerant Recovery".
Illustration 1 g00604540
Loosen two bolts (2) and (4) and the washers that hold idler pulley (1) to bracket assembly (5). Remove V-belt (3) from refrigerant compressor (6) and place V-belt (3) aside.
Illustration 2 g00604542
Disconnect wire harness (7) at the electrical connection. Disconnect wire harness (8) at the electrical connection.
Illustration 3 g00604543
Remove bolt (9) and the washer that holds adjustment rod (10) to bracket assembly (5). Remove nut (11) and the washer that holds adjustment rod (10) to refrigerant compressor (6). Remove adjustment rod (10) from refrigerant compressor (6).
Illustration 4 g00604544
Illustration 5 g00604531
Disconnect two hose assemblies (12) and (13) from refrigerant compressor (6).
Remove two bolts (14) and (15) the washers that hold refrigerant compressor (6) to bracket assembly (5).
Illustration 6 g00604546
Position a suitable lifting sling (not shown) around refrigerant compressor (6). Remove bolt (16) and the washer that holds refrigerant compressor (6) to bracket assembly (5). Remove refrigerant compressor (6) from bracket assembly (5). The weight of refrigerant compressor (6) is 40 kg (89 lb). Installation Procedure
Verify that all of the components are clean and free of foreign material prior to installation. Inspect all of the O-ring seals and the components for wear. Replace the O-ring seals and the components, if necessary.
Lubricate all O-ring seals with the lubricant that is being sealed.
Illustration 7 g00604546
Position a suitable lifting sling (not shown) around refrigerant compressor (6). Position refrigerant compressor (6) to bracket assembly (5), as shown. Install bolt (16) and the washers that hold refrigerant compressor (6) to bracket assembly (5). The weight of refrigerant compressor (6) is 40 kg (89 lb).