0336242 JOHNSON COVER, Handle

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     1U-7307     Governor Repair Fixture (1)     1    
B     1U-7635     Clevis Driver (1)     1    
C     1U-7606     Servo Block (1)     1    
D     1U-7277     Pin Punch     1    
E     1P-1857     Retaining Ring Pliers     1    
F     1P-1855     Retaining Ring Pliers     1    
G     1U-7309     Shim Adjustment Tool (1)     1    
H     1U-7313     Gauge Block (1)     1    
I     1U-7312     Calibration Plate (1)     1    
J     1U-7314     Weight (1)     1    
K     1U-7308     Shim Adjustment Tool (1)     1    
( 1 ) Part of the former 1U-9088 Tool Group
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Inspect all parts of the governor upon assembly. For information on the reusability of components in the governor, refer to the Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines Equipped with Mechanical Unit Injectors (MUI)". For information on cleaning the components in the governor, refer to the The Cleaning Guide, SEBF8354, "Equipment And Chemical Recommendations Reference Manual".Note: Refer to Chart A "Parts to be Replaced During Rebuild" in Guideline For Reusable Parts And Salvage Operations, SEBF8434 for a list of components that need to be replaced during a governor rebuild. It is not necessary to replace the components in Chart A "Parts to be Replaced During Rebuild" if the governor is in the shop for a bench test or for minor repair.Note: Refer to Chart B "Parts Replacement Chart" in Guideline For Reusable Parts And Salvage Operations, SEBF8434 for a list of components that need to be replaced when the servo assembly is serviced.Note: Put clean engine oil on all parts before assembly. Ensure that all of the oil passages in the governor are clean and free of obstructions.
Illustration 1 g00615706
(100) Nut (101) O-ring seal (102) O-ring seal (103) Valve cavity (104) Spring (105) Piston assembly (106) Seal (107) Fitting (108) O-ring seal (109) Setscrew (110) O-ring seal (111) Nut (112) CoverNote: Inspect all of the governor parts for wear or for damage. If any of the governor parts are worn or damaged, use new parts for replacement.
Install spring (104) and seal (106) onto piston assembly (105) .
Insert piston assembly (105) into the access hole. Thread the collar onto piston assembly (105) from the opposite side of the access hole. Thread the collar onto the piston assembly until the alignment pin contacts the housing. As the alignment pin makes contact with the housing, rotate the alignment pin until the alignment pin engages in the alignment slot.
Insert a socket through the access hole and tighten piston assembly (105) until the piston assembly bottoms out.
Install O-ring seal (108), fitting (107), nut (100) and setscrew (109) .Note: Back out the setscrew for the adjusting procedure. Refer to the Testing and Adjusting, "Adjusting a New or Rebuilt Governor (Type VI)" topic in this manual for additional information.
Install O-ring seals (101) and (102) and put the dual horsepower mechanism in position on the governor.
Illustration 2 g00655999
(97) Bolt (98) Solenoid (99) Wire retaining clip
Apply 9S-3263 Thread Lock Compound to three bolts (97) and install the bolts.
Install solenoid (98) on the dual horsepower mechanism.
Install wire retaining clip (99) .
Install O-ring seal (110) and cover (112) for the setscrew.