0434366 JOHNSON COVER, Handle


0434366 COVER, Handle JOHNSON AM55RSLD, HJ25FPO, HJ25FPV, HJ45RCLEDS, HJ45RCLEUC, HJ55RSLC, HJ55RSLW, J105WRLEES, J105WRLSIF, J105WRLSSC, J25RWEOS, J25WREEN, J25WRLSIR, J25WRLSSC, J40WREES, J40WRLSIR, J40WRLSSC, J45RCEOD, J45RCERE, J55APRL, J55APRLSRA, J55MLSRC, J55MRL, J55RSLG, COVER
0434366 COVER, Handle JOHNSON
Rating:
38

Buy COVER, Handle 0434366 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 7
 

BRP JOHNSON entire parts catalog list:

AM55RSLD, J55WREES, J55WRLEES, J55WRYEES 1999
HJ25FPO, HJ25RSLO, J25RWEDC, J25RWLEDC 1996
HJ25FPV, HJ25RLSV, J25RWEUR, J25RWLEUR, SJ25RPLV, SJ25RPV 1997
HJ45RCLEDS, J45RCLEDS, SJ45RSLH 1996
HJ45RCLEUC, J45RCLEUC, SJ45RSLB 1997
HJ55RSLC, J55RSLC, SJ55RSC, SJ55RSLC, SJ55RSYC 1997
HJ55RSLW, J55RSLW, SJ55RSLW, SJ55RSW, SJ55RSYW 1996
J105WRLEES, J105WRYEES 1999
J105WRLSIF, J105WRYSIF 2001
J105WRLSSC, J105WRYSSC 2000
J25RWEOS, J25RWLEOS 1995
J25WREEN, J25WREES, J25WRLEEN, J25WRLEES 1999
J25WRLSIR, J25WRSIR 2001
J25WRLSSC, J25WRSSC 2000
J40WREES, J40WRLEES, J40WRYEES 1999
J40WRLSIR, J40WRSIR, J40WRYSIR 2001
J40WRLSSC, J40WRSSC, J40WRYSSC 2000
J45RCEOD, J45RCLEOD 1995
J45RCERE, J45RCLERE 1994
J55APRL 2003
J55APRLSRA, J55APRLSRG 2004
J55MLSRC, J55MLSRG 2004
J55MRL 2003
J55RSLG 1995
J55RWLERE 1994
J55WRLSIR, J55WRSIR, J55WRYSIR 2001
J55WRLSOE, J55WRYSOB 2005
J55WRLSRB, J55WRLSRG, J55WRYSRM 2004
J55WRLSSC, J55WRSSC, J55WRYSSC 2000
J55WRLSTM 2003
J65RSLC 1995
J65RSLM, SJ65RSLM, SJ65RSYM 1996
J65RSLZ2, SJ65RSLZ2, SJ65RSYZ2 1997
J65WRLEEO, J65WRLEES, J65WRYEEO, J65WRYEES 1999
J65WRLSIR, J65WRYSIR 2001
J65WRLSSC, J65WRYSSC 2000
SJ105RWLH, SJ105RWYH 1998
SJ105RWLH, SJ105RWYH 1998
SJ105RWLP, SJ105RWYP 1997
SJ105RWLP, SJ105RWYP 1997
SJ125RWYJ 1997
SJ125RWYN 1998
SJ125RWYV 1996
SJ25RPLP, SJ25RPP 1998
SJ40RPB, SJ40RPLB, SJ40RPYB 1997
SJ40RPH, SJ40RPLH, SJ40RPYH 1996
SJ40RPLT2, SJ40RPT2, SJ40RPYT2 1998
SJ40RSLD 1997
SJ40RSLR 1998
SJ40RSLZ 1996
SJ55RSLM2, SJ55RSM2, SJ55RSYM2 1998
SJ65RSLD, SJ65RSYD 1998

Information:

315B, 322B, 325B, and 330B
Illustration 1 g00670058
Attachment Of The Cable For The Governor Actuator (315B, 322B, 325B And 330B)
(1) Accelerator Cable
(2) Nut
(3) Support
(4) Bellows
(5) Lever
Turn the nut (2) and the locknut of the accelerator cable (1) in the counterclockwise direction until the nuts are separated.
Insert the threaded "L" end of the accelerator cable (1) through the hole in the lever (5). Install the nut in order to hold the cable in position.
Insert the other threaded portion of the accelerator cable (1) into the notch of the support (3).
Turn the lever (5) in the counterclockwise direction to the position of high idle.
Hold the lever (5) against the position of HIGH IDLE STOP. Then, turn the nut (2) clockwise until the slack is removed from the bellows (4). The nut (2) should be tightened for approximately two turns more.
Tighten the locknut against the support (3).
Ensure that the nut (2) remains in position while the locknut is tightened against the support (3).
Reinstall the two clamps to the accelerator cable (1). Do not allow the cable (1) to twist.Note: Ensure that the governor lever is in contact with the high idle stop. Also, ensure that the nut (2) is correctly tightened in order to ensure that the accelerator cable has the correct tension. The setting of the engine speed or an overload condition of the governor actuator could result if the cable is not tightened correctly.Note: When the current governor is being used, the following conditions will be applicable:
When the accelerator cable (1) is disconnected from the governor lever and the engine speed dial is in a position rather than 10, the initial calibration procedure is required.
No initial setting is required, if the accelerator cable (1) is disconnected from the governor lever and the engine speed dial is positioned at 10. However, the initial setting is required, when electricity is sent to the governor actuator.311B, 312B, and 320B
Illustration 2 g06603975
Governor Actuator
(1) Governor Actuator
Illustration 3 g06603977
(A) Engine side
(2) Accelerator Cable
Illustration 4 g00670071
Cable For The Governor Actuator
(2) Accelerator Cable
(3) Support
(4) Bellows
(5) Lever
(6) Decelerator Cable
(7) Nut
(8) Nut
(9) Bellows
(10) Locknut
(11) Locknut
Turn the nut (10) and the locknut of the accelerator cable (2) in the counterclockwise direction until the nuts are separated.
Insert the threaded end "L" of the accelerator cable (2) through the hole in the lever (5). Install the nut in order to hold the cable in position.
Insert the other threaded portion of the accelerator cable (2) into the notch of the support (3).
Turn the lever (5) to the position of high idle.
Hold the lever (5) against the position of HIGH IDLE STOP. Then, turn the nut (10) clockwise until the slack is removed from bellows (9). The nut (10) should be tightened for approximately two turns more.
Tighten the locknut (8) against the support (3). Ensure that the nut (10) remains in position on the threaded portion of the accelerator cable (2) while the locknut is being tightened against the support (3).
Reinstall the two clamps to the accelerator cable (2). Do not allow the cable (2) to twist.
Insert the joint of the decelerator cable (6) through the hole in the lever (5). Install the nut (11) to hold the cable (6) in position.
Loosen the nut (7) and the locknut (11) on decelerator cable (6).
Insert the other threaded portion of the decelerator cable (6) into the notch of the support (3).
Hold the lever (5) against the position of HIGH IDLE STOP and turn the nut (7) clockwise until the slack is removed from the bellows (4). The nut (7) should be loosened for two turns more.
Tighten the locknut (11) against the support (3). Ensure that the nut (7) remains in position while the nut (7) is tightened against the support (3).Note: Ensure that the governor lever is in contact with the high idle stop. Also, ensure that the nut (8) is correctly tightened in order to ensure that the accelerator cable (2) has the correct tension. The setting of the engine speed and an overload of the governor actuator could result, if the cable is not correctly tightened.Note: When the current governor actuator is being used the following conditions are applicable:
The initial setting should always be performed when the governor actuator is being supplied with power.Note: If the current governor, that is being used, is a governor from spare parts, then do not send electricity to the governor. The initial setting of the governor should always be performed because the governor may have received electricity.Calibration Of The Governor Actuator
Note: For more information, see the topic Testing And Adjusting, "Governor Actuator".
Start the engine. Perform the calibration procedure for the governor actuator.
Clear the error log, after the calibration procedure has been correctly performed.Note: For more information, see Testing And Adjusting, "Error Log".


Parts cover JOHNSON:

0387336
COVER ASSY. & BUSHING
0387336 COVER ASSY. & BUSHING
50R79C, 55E76E, 55E77D, 55E78S, 55E79C, 70EL76D, 70EL77S, 70EL78C, 70EL79R, 75ELR76D, 75ELR77S, 75ELR78C, 75ELR79R, AM55RSLD, HJ45RCLEDS, HJ45RCLEUC, HJ55RSLC, HJ55RSLW, HJ55WMLM, HJ55WMLZ, J35AELCDE, J35AELCUD, J40AELCCS, J40ECDE, J40ECOB, J40ECRM,
0321673
COVER, Mount bracket, lower
0321673 COVER, Mount bracket, lower
70EL78C, 70EL79R, 75ELR78C, 75ELR79R, BJ50DTLEDC, BJ50DTLEUR, BJ60ELEDR, BJ60ELEUA, BJ60TLECM, BJ70ELECB, BJ70ELEDA, BJ70ELEUM, BJ70PLEEE, BJ70PLSIS, BJ70PLSSD, J40JPLEEC, J40JPLSIA, J40JPLSSR, J50DTLECA, J50DTLEOS, J50TTLECA, J50TTLEDC, J50TTLEOS, J
0388651
COVER ASSY.
0388651 COVER ASSY.
70EL78C, 70EL79R, 75ELR78C, 75ELR79R, BJ50DTLEDC, BJ50DTLEUR, BJ60ELEDR, BJ60ELEUA, BJ60TLECM, BJ70ELECB, BJ70ELEDA, BJ70ELEUM, BJ70PLEEE, BJ70PLSIS, BJ70PLSSD, J40JPLEEC, J40JPLSIA, J40JPLSSR, J50DTLECA, J50DTLEOS, J50TTLECA, J50TTLEDC, J50TTLEOS, J
0433561
COVER&PLUG AY
0433561 COVER&PLUG AY
J40ECEC, J40EEIA, J40EENJ, J40EERE, J40EESR, J40EETB, J45RCE, J45RCEIA, J45RCENM, J45RCERE, J45RCESR, J45RCETB, J48ESLCER, J48ESLCER, J48ESLEIM, J48ESLEIM, J48ESLENB, J48ESLENB, J48ESLERD, J48ESLERD, J48ESLESA, J48ESLESA, J48ESLETE, J48ESLETE, J50BEC
0434588
COVER, Shift rod
0434588 COVER, Shift rod
BJ40EECR, BJ40EEDS, BJ40EEEA, BJ40EEUC, BJ40ELSIF, BJ40ELSSM, BJ50BEEDS, BJ50EEER, BJ50ELSIF, BJ50ELSSA, BJ50ESECC, BJ50RLEUC, J40EEOD, J40EERE, J40EETB, J40PLSNF, J40RLSNF, J48ESLEDC, J48ESLEDC, J48ESLEOS, J48ESLEOS, J48ESLERD, J48ESLERD, J48ESLETE,
0338632
COVER, Thermostat
0338632 COVER, Thermostat
BJ115ELEDR, BJ115ELEUA, BJ115GLECM, BJ115PLEEM, BJ115PLSIE, BJ115PLSSB, BJ150ELECD, BJ150ELEDB, BJ150ELEUC, BJ175EXECD, BJ175EXEDB, BJ175EXEUC, BJ175PLEES, BJ175PLSIF, BJ175PLSSC, BJ90ELEDR, BJ90ELEUA, BJ90PLEEB, BJ90PLSID, BJ90PLSSE, BJ90SLECM, J100
0436951
 
0436951 COVER, Carburetor
AM55RSLD, BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25EECE, BJ25EEDM, BJ25EEED, BJ25EEUB, BJ25ELSIC, BJ25ELSSS, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, BJ30EECS, BJ30EEDE, BJ30EEEC, BJ30E
0340785
COVER, Exh. hsg., rear
0340785 COVER, Exh. hsg., rear
AM55RSLD, HJ45RCLEDS, HJ45RCLEUC, HJ55RSLC, HJ55RSLW, HJ55WMLM, HJ55WMLZ, J40WREES, J40WRLSIR, J40WRLSSC, J45RCEOD, J45RCERE, J55APRLSOM, J55APRLSRA, J55MLSOR, J55MLSRC, J55RSLG, J55RWLERE, J55WRLSIR, J55WRLSOE, J55WRLSRB, J55WRLSSC, J55WRLSTM, SJ40R
Back to top