5036171 COVER, CYLINDER HEAD JOHNSON
J10BL4SUM, J10EL4SDA, J10EL4SOR, J10R4SDM, J10R4SUB, J10RL4SDM, J10TBL4SDE, J10TBL4SUD, J10TE4SDM, J15EL4SDC, J15EL4SOS, J15EL4SUR, J15R4SDM, J15R4SUB, J15RL4SDM, J15TE4SDM, J15TE4SUB
COVER
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- CYLINDER HEAD » 5036171
J10EL4SOR, J10R4SOA, J10RL4SOA, J10TBL4SOB, J10TE4SOA, J10TEL4SOA 2005
J10R4SDM 2006
J10R4SUB, J10RL4SUB 2007
J10RL4SDM 2006
J10TBL4SDE 2006
J10TBL4SUD, J10TE4SUB, J10TEL4SUB 2007
J10TE4SDM, J10TEL4SDM 2006
J15EL4SDC 2006
J15EL4SOS, J15R4SOA, J15RL4SOA, J15TE4SOA, J15TEL4SOA 2005
J15EL4SUR 2007
J15R4SDM 2006
J15R4SUB, J15RL4SUB 2007
J15RL4SDM 2006
J15TE4SDM, J15TEL4SDM 2006
J15TE4SUB, J15TEL4SUB 2007
Information:
Table 1
Diagnostic Trouble Codes
Code Description Conditions Present Response
636-2 Crankshaft position sensor pulse number error Open circuit or short circuit of sensor / harness.
Battery voltage is normal
Sensor supply voltage VCC# is normal
Engine is not stalled
Pulse count per rotation is not 58 teeth for 10 times or more.
Faulty starting.
Engine vibration increases slightly. Engine derates 25%
Warning Level 2
636-8 No crankshaft position sensor signal Open circuit or short circuit of sensor / harness.
Failure of sensor.
Battery voltage is normal
Sensor supply voltage is normal
Engine is not stalled.
No recognition of crankshaft sensor pulse for 10 times or more.
Faulty starting.
Engine vibration increases slightly.
636-7 Engine Position Sensor – Large phase shift between Camshaft and Crankshaft position sensors Large phase shift between NE pulse and G pulse
Battery voltage is normal
Sensor supply voltage VCC# is normal
Crankshaft and crankshaft signals are normal
Phase difference between NE pulse and G pulse is within +30 and - 20 degree for 2 times or more.
723-2 Camshaft sensor Pulse Number Error Open circuit or short circuit of sensor / harness.
Failure of sensor.
Battery voltage is normal
Sensor supply voltage VCC# is normal
Engine is not stalled
Pulse count per rotation is not 3 teeth for 4.4 rotations of crankshaft sensor pulse.
Engine hesitates at start-up. None
723-8 No Input of Camshaft Position Pulse Open circuit or short circuit of sensor / harness.
Failure of sensor.
Battery voltage is normal
Sensor supply voltage VCC# is normal
Engine is not stalled
No recognition of Camshaft sensor pulse for 4.4 rotations of crankshaft sensor pulse.
Engine hesitates at start-up. None The crankshaft position sensor is the primary speed/timing sensor. The camshaft position sensor is the secondary speed/timing sensor. The position sensorare used to determine the piston height and engine speed.If the engine is running and the signal from the primary engine speed/timing sensor is lost, the engine will derate. Loss of the signal from the secondary engine speed/timing sensor during engine operation will not result in any noticeable change in engine performance.During startup the loss of either the crankshaft or camshaft speed/timing sensor will result in hard starting.The loss of both the crankshaft and camshaft speed/timing sensors will result in no start or the engine will stop.
Illustration 1 g06111910Note: 2 and 8 codes are detecting an open circuit or short circuit of the sensor or the harness. These are almost always harness-related.Note: 7 codes measure a large phase shift between the crankshaft position sensor and the camshaft position sensor.
Table 2
Troubleshooting Test Step Value Expected Results
1. Check Supply Voltage at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the crankshaft position sensor.
C. Turn the keyswitch to the ON position.
D. Measure the voltage between terminals 1 and 3 on the harness side. The voltage should be 5V.
5 VDC
Result: The voltage was OK.
Proceed to Test Step 2.
Result: The voltage was NOT OK.
There is a problem in the wiring harness. Replace the engine harness.
2. Remove the Sensor
A. Check for signs of contact with the sensor or magnetic material.
Sensor
Result: There is no magnetic material.
Replace the sensor.
Result: There is magnetic material. Clean off sensor and reinstall. Confirm that the issue is resolved. Determine the source of the magnetic material if needed.
If this procedure did not correct the issue, contact your Technical Communicator (TC).
Parts cover JOHNSON:
5031499
5031499 COVER, STEERING ADJUSTER
BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC, BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J10BL4SUM, J10EL4SDA, J10EL4SOR, J10EL4SRC, J10R4SDM, J10R4SNF, J10R4SR, J10R4STC, J10R4SUB, J10RL4SDM, J10TBL
5032722
5032722 COVER ASSY, THERMOSTAT
J10EL4SOR, J10EL4SRC, J10R4SNF, J10R4SR, J10R4STC, J15EL4SOS, J15R4SNF, J15R4SR, J15R4STC, J15RL4SR
5034041
5034041 COVER ASSY, THERMOSTAT
J10EL4SOR, J10EL4SRC, J10R4SR, J10R4STC, J15EL4SOS, J15R4SR, J15R4STC, J15RL4SR
5036513
5036511
5036512
5036510
5036510 *COVER
J10EL4SOR, J10R4SDM, J10R4SUB, J10RL4SDM, J10TBL4SDE, J10TBL4SUD, J10TE4SDM, J15EL4SOS
5035796
5035796 COVER, PROTECTION ANODE
BJ25E4SUC, BJ25R4SUC, BJ25TE4SUC, BJ60PL4SDM, BJ60PL4SOA, BJ70PL4SDM, BJ70PL4SOA, J10BL4SUM, J10EL4SDA, J10EL4SOR, J10R4SDM, J10R4SUB, J10RL4SDM, J10TBL4SDE, J10TBL4SUD, J10TE4SDM, J15EL4SDC, J15EL4SOS, J15EL4SUR, J15R4SDM, J15R4SUB, J15RL4SDM, J15TE