AVS Marine

0322928 JOHNSON CRANKSHAFT


  1. Home
  2. Parts
  3. Johnson
  4. Crankshaft
  5. 0322928
0322928 CRANKSHAFT JOHNSON 50R79C, 55E78S, 55E79C, J50BECIC, J50BECNR, J50BECTA, J50ECSR, J55RCIM, J55RLCSA, J60ECIA, J60ECNM, J60ECSR, J60ECTB CRANKSHAFT
0322928 CRANKSHAFT JOHNSON
Price: query
Rating:
78

Buy CRANKSHAFT 0322928 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
Beck Arnley 032-2928 Engine Cylinder Head Gasket Set
$63.78
 

25-11-2018
40 Hundredths Pounds
Beck Arnle: Beck Arnley
Beck Arnley 032-2928 Engine Cylinder Head Gasket Set
Matches OE form, fit, and function||Contains gaskets and seals necessary for a complete upper engine repair||Quality construction and materials for optimal sealing||Packaged in clear plastic for easy visibility and identification of all components||Application specific to ensure a correct fit for your vehicle
Number on catalog scheme: 12
Scheme 0322928
 

Compatible models:

50R79C   55E78S   55E79C   J50BECIC   J50BECNR   J50BECTA   J50ECSR   J55RCIM   J55RLCSA   J60ECIA   J60ECNM   J60ECSR   J60ECTB   JOHNSON

BRP JOHNSON entire parts catalog list:

50R79C, 50RL79C 1979
55E78S, 55EL78S 1978
55E79C, 55EL79C 1979
J50BECIC, J50BELCIC 1981
J50BECNR, J50BELCNR 1982
J50BECTA, J50BELCTA, J50TELCTA 1983
J50ECSR, J50ELCSR 1980
J55RCIM, J55RLCIM 1981
J55RLCSA 1980
J60ECIA, J60ECIH, J60ELCIA, J60ELCIH, J60TLCIA, J60TLCIH 1981
J60ECNM, J60ELCNM, J60TLCNM 1982
J60ECSR, J60ELCSR 1980
J60ECTB, J60ELCTB, J60TLCTB 1983

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
D 298-5564 T40 Torx Socket 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Start By:
Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install" for the correct procedure.
Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable. Care must be taken in order to ensure that the fuel injection pump timing is not lost during the removal of the front gear group. Carefully follow the procedure in order to remove the gear group.
Illustration 1 g01992076
Remove plug (2) from the cylinder block. Remove O-ring seal (1) from the plug.
Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead center on the compression stroke. Refer to System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure.
Install Tooling (C) through Hole (W) in order to lock the crankshaft.
Illustration 2 g03383026
Loosen nuts (4) on all rocker arms (5). Use Tooling (D) in order to loosen adjusters (3) on all rocker arms (5) until all valves are fully closed. Note: Failure to ensure that ALL adjusters are fully unscrewed can result in contact between the valves and pistons.
Illustration 3 g03383038
Install Tooling (B) through Hole (X) in camshaft gear (7) into the front housing. Use Tooling (B) in order to lock the camshaft in the correct position. Refer to System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure.
Illustration 4 g03383040
Alignment of timing marks
Mark gear (7), gear (8), and gear (9) in order to show alignment. Refer to Illustration 4. Note: Identification will ensure that the gears can be installed in the original alignment.
Remove Tooling (B) and Tooling (C).
Remove fuel pump gear (9). Refer to Disassembly and Assembly, "Fuel Pump Gear - Remove and Install" for the correct procedure.
Remove camshaft gear (7). Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install" for the correct procedure.
Remove idler gear (8). Refer to Disassembly and Assembly, "Idler Gear - Remove and Install" for the correct procedure. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 230-6284 Timing Pin (Camshaft) 1
C 136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
D 298-5564 T40 Torx Socket 1
E


Back to top