0328326 JOHNSON CYL.HEAD,Port 235 S model only


0328326 CYL.HEAD,Port 235 S model only JOHNSON J150TLCOS, J150TLCRD, J150TLCTB, J175TLCOC, J175TLCTD, J185TLCOC, J185TLCRS, J200TLCTD, J235TLCOR, J235TLCRC, J235TLCTD CYL
0328326 CYL.HEAD,Port 235 S model only JOHNSON
Rating:
8

Buy CYL.HEAD,Port 235 S model only 0328326 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 29
 

BRP JOHNSON entire parts catalog list:

J150TLCOS, J150TXCOS 1985
J150TLCRD, J150TXCRD 1984
J150TLCTB, J150TLCTE, J150TXCTB, J150TXCTE 1983
J175TLCOC, J175TXCOC 1985
J175TLCTD, J175TLCTE, J175TXCTD, J175TXCTE 1983
J185TLCOC, J185TXCOC 1985
J185TLCRS, J185TXCR 1984
J200TLCTD, J200TLCTS, J200TXCTD, J200TXCTS 1983
J235TLCOR, J235TXCOR 1985
J235TLCRC, J235TXCRC 1984
J235TLCTD, J235TLCTS, J235TXCTD, J235TXCTS 1983

Information:


Use of commercially available cooling system cleaners may cause damage to cooling system components. Use only cooling system cleaners that are approved for Caterpillar engines.
When any servicing or repair of the engine cooling system is performed, the procedure must be performed with the engine on level ground. Level ground will allow you to check accurately the coolant level. This procedure will also help in avoiding the risk of introducing an air lock into the coolant system.
Note: Inspect the water pump and the water temperature regulator after the cooling system has been drained. This inspection is a good opportunity to replace the water pump, the water temperature regulator, and the hoses, if necessary.Drain
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly to relieve any pressure. Remove the cooling system filler cap.Note: Refer to Operation and Maintenance Manual, "General Hazard Information" for information on containing a fluid spillage.
Illustration 1 g06302798
Remove the drain plug (1). Open the drain cock or remove the drain plug on the radiator.Allow the coolant to drain into a suitable container.
Properly dispose of the drained material. Obey local regulations for the disposal of the material.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
Flush
Flush the cooling system with clean water to remove any debris.
Install connection hose. Clean the drain plugs. Install the drain plugs and tighten securely.
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with a mixture of clean water and Caterpillar Fast Acting Cooling System Cleaner. Add 0.5 L (1 pt) of cleaner per 15 L (4 US gal) of the cooling system capacity. Install the cooling system filler cap.
Start and run the engine at low idle for a minimum of 30 minutes. The coolant temperature should be at least 85° C (185° F).
Improper or incomplete rinsing of the cooling system can result in damage to copper and other metal components.To avoid damage to the cooling system, make sure to completely flush the cooling system with clear water. Continue to flush the system until all signs of the cleaning agent are gone.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly to relieve any pressure. Remove the cooling system filler cap. Remove the connection hose or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Install the connection hose.
The drain plug O rings on the engine block must be replaced. Clean the drain plugs and install new O ring seal. Install the drain plugs and tighten securely.Cooling Systems with Heavy Deposits or Plugging
Note: For the following procedure to be effective, there must be some active flow through the cooling system components.
Flush the cooling system with clean water to remove any debris.
Clean the drain plugs. Install the drain plugs and tighten securely.
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with a mixture of clean water and Caterpillar Fast Acting Cooling System Cleaner. Add 0.5 L (1 pt) of cleaner per 3.8 to 7.6 L (1 to 2 US gal) of the cooling system capacity. Install the cooling system filler cap.
Start and run the engine at low idle for a minimum of 90 minutes. The coolant temperature should be at least 85° C (185° F).
Improper or incomplete rinsing of the cooling system can result in damage to copper and other metal components.To avoid damage to the cooling system, make sure to completely flush the cooling system with clear water. Continue to flush the system until all signs of the cleaning agent are gone.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plug. Allow the water to drain. Flush the cooling system with clean water.
The drain plug O rings on the engine block must be replaced. Clean the drain plugs and install new O ring seal. Install the drain plugs and tighten securely.Fill
Do not fill the cooling system faster than 5 L (1.3 US gal) per minute to avoid air locks.Cooling system air locks may result in engine damage.
Fill the cooling system with the coolant/antifreeze. Refer to this Operati


Parts cyl JOHNSON:

0325557
 
0325557 CYL. HEAD, Stbd., 150, 175
J150TLCIA, J150TLCNM, J150TLCSF, J150TLCTB, J175TLCIH, J175TLCNB, J175TLCSA, J175TLCTD, J200TLCIH, J200TLCNE, J200TLCSF, J200TLCTD, J235TLCIB, J235TLCNE, J235TLCSM, J235TLCTD
0327124
 
0327124 CYL. HEAD, Port 235
J150TLCIA, J150TLCNM, J150TLCTB, J175TLCIH, J175TLCNB, J175TLCTD, J200TLCIH, J200TLCNE, J200TLCTD, J235TLCIB, J235TLCNE, J235TLCTD
0328325
 
0328325 CYL.HEAD,Stbd.,150,175,200
J150CXCCA, J150CXCEM, J150CXEIE, J150CXESB, J150TLCDC, J150TLCOS, J150TLCRD, J150TLCTB, J150TLCUR, J155WTLCDR, J155WTLCOC, J155WTLCRS, J155WTLCUA, J155WTLEIB, J155WTLENE, J155WTLESM, J155WTLZ, J175STLACM, J175STLCEB, J175STLEID, J175STLESE, J175TLCDR
0328324
 
0328324 CYL.HEAD,Port 150,175,200
J150CXCCA, J150CXCEM, J150CXEIE, J150CXESB, J150TLCDC, J150TLCOS, J150TLCRD, J150TLCTB, J150TLCUR, J155WTLCDR, J155WTLCOC, J155WTLCRS, J155WTLCUA, J155WTLEIB, J155WTLENE, J155WTLESM, J155WTLZ, J175STLACM, J175STLCEB, J175STLEID, J175STLESE, J175TLCDR
Back to top