0335841 JOHNSON CYLINDER HEAD


0335841 CYLINDER HEAD JOHNSON BJ3REDS, BJ4BREDS, BJ4BREUC, J3REIA, J3RENM, J3REOD, J3RERE, J3RETB, J3REUC, J4BRECRJ, J4REEA, J4REIA, J4RENM, J4REOD, J4RERE, J4RETB, J4RLSIB, J4RLSSM CYLINDER
0335841 CYLINDER HEAD JOHNSON
Rating:
13

Buy CYLINDER HEAD 0335841 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 24
 

BRP JOHNSON entire parts catalog list:

BJ3REDS, SJ3REDS 1996
BJ4BREDS, BJ4BRLEDS, BJ4REDS, BJ4RLEDS, J4REDS, J4RLEDS, SJ4REDS, SJ4RLEDS 1996
BJ4BREUC, BJ4BRLEUC, J4REUC, J4RLEUC 1997
J3REIA 1991
J3RENM 1992
J3REOD 1995
J3RERE 1994
J3RETB 1993
J3REUC 1997
J4BRECRJ, J4BRLECRJ 1998
J4REEA, J4RLEEA 1999
J4REIA, J4RLEIA 1991
J4RENM, J4RLENM 1992
J4REOD, J4RLEOD 1995
J4RERE, J4RLERE 1994
J4RETB, J4RLETB 1993
J4RLSIB, J4RSIB 2001
J4RLSSM, J4RSSM 2000

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 589-7433 Link Bracket 2
B - Loctite ® C5-A (North America) -
Loctite ® 8008 (Outside North America) -
C 207-1601 Rubber Lubricant 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the spacer plate and the surface of the cylinder block are clean.
Illustration 1 g06553514
Ensure that the surface of the spacer plate gasket and the surface of the cylinder block are clean. Do not use a gasket adhesive on these surfaces.
Install a new gasket (18) on the dowels in the cylinder block.
Install O-ring seal (19).
Illustration 2 g06553497
Install spacer plate (17) and cylinder head gasket (16) on the dowels in the cylinder block.
Check the cylinder liner projection. Refer to Testing and Adjusting, "Cylinder Liner Projection" for the correct procedure.
Illustration 3 g06553298
Install seals (13) and seals (14).
Apply Tooling (C) to the bore of the inlet tube assembly. Install O-ring seal (11) in the inlet tube assembly.
Install gasket (12) on the exhaust manifold.
Install O-ring seal (15) on the dowel.
Illustration 4 g06554112
Install plug (20).
Illustration 5 g06554127
Install Tooling (A) onto cylinder head assembly (10). Attach a suitable lifting device to Tooling (A). The weight of cylinder head assembly (7) is approximately 47 kg (104 lb).
Ensure that the bottom of the cylinder head assembly is thoroughly clean.
Illustration 6 g06552788
Lift the cylinder head assembly into position on the cylinder block. Install bolts (8) and bolts (9) according to the instructions in Step 15 or Step 16.Note: Only 216 mm (8.5 inch) bolts (8) can be used for the following torque procedures.Note: Refer to Specifications, "Cylinder Head".
Remove Tooling (A) from the cylinder head.
Illustration 7 g06554187
Tightening sequence with 362-8264 Cylinder Head Gasket (MLS) and 519-7297 Spacer Plate (Iron).Note: Refer to Illustration 7 for the correct tightening sequence.
Coat the threads of the bolts with clean engine oil.
Tighten bolt (1) through bolt (8) to a torque of 30 5 N m (22 4 lb ft).
Tighten bolt (1) through bolt (8) to a torque of 145 15 N m (107 11 lb ft).
Tighten bolt (1) through bolt (8) to a torque of 145 15 N m (107 11 lb ft).
Turn bolt (1) through bolt (8) an angle of 180 5 degrees.
Tighten bolts (9) and (10) to a torque of 55 10 N m (40 7 lb ft).
Illustration 8 g06554195
Tightening sequence with 110-6991 Cylinder Head Gasket (Cellulose) and 110-6994 Spacer Plate (Aluminum) or 362-9677 Spacer Plate (Aluminum).Note: The cellulose head gasket cannot be used with an iron spacer plate.Note: Refer to Illustration 8 for the correct tightening sequence.
Tighten bolt (1) through bolt (8) to a torque of 30 5 N m (22 4 lb ft).
Tighten bolt (1) through bolt (8) to a torque of 200 15 N m (148 11 lb ft).
Tighten bolt (1) through bolt (8) again to a torque of 200 15 N m (148 11 lb ft).
Turn bolt (1) through bolt (8) to an angle of 180 degrees.
Tighten bolt (9) and bolt (10) to a torque of 55 10 N m (41 7 lb ft).


Parts cylinder JOHNSON:

0433940
 
0433940 CYLINDER & C'CASE ASSY.
BJ3REDS, BJ4BREDS, J3REIA, J3RENM, J3REOD, J3RERE, J3RETB, J4REIA, J4RENM, J4REOD, J4RERE, J4RETB
0433418
 
0433418 CYLINDER & C'CASE ASSY.
BJ3REDS, BJ4BREDS, BJ4BREUC, J3REIA, J3RENM, J3REOD, J3RERE, J3RETB, J3REUC, J4REIA, J4RENM, J4REOD, J4RERE, J4RETB
0435346
 
0435346 CYLINDER & C'CASE ASSY.
BJ3REDS, BJ4BREDS, BJ4BREUC, J3REOD, J3REUC, J4BRECRJ, J4REEA, J4REOD, J4RLSIB, J4RLSSM
Back to top