0398758 JOHNSON CYLINDER & C'CASE ASSY.


0398758 CYLINDER & C'CASE ASSY. JOHNSON J250CXATF, J250CXEIE, J250CXEND, J275CXCCA, J300CXCCA, J300CXCEM, J300CXEIE, J300CXEND, J300CXESB, J300CXETF CYLINDER
0398758 CYLINDER & C'CASE ASSY. JOHNSON
Rating:
78

Buy CYLINDER & C'CASE ASSY. 0398758 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

BRP JOHNSON entire parts catalog list:

J250CXATF, J250CXATS, J250CXETF, J250CXETS, J250CZATF, J250CZATS, J250CZETF, J250CZETS, J250TXATF, J250TXATS, J250TXETF, J250TXETS, J250TZATF, J250TZATS, J250TZETF, J250TZETS 1993
J250CXEIE, J250TXEIE 1991
J250CXEND, J250CZEND, J250TXEND, J250TZEND 1992
J275CXCCA, J275PLCCA, J275PXCCA 1988
J300CXCCA, J300PLCCA, J300PXCCA 1988
J300CXCEM, J300PLCEM, J300PXCEM 1989
J300CXEIE, J300PLEIE, J300PXEIE 1991
J300CXEND, J300PLEND, J300PXEND 1992
J300CXESB, J300PLESB, J300PXESB 1990
J300CXETF, J300CXETS, J300PLETF, J300PLETS, J300PXETF, J300PXETS 1993

Information:


Table 2
Associated Diagnostic Trouble Codes
J1939 Code CDL Code
5392-31 E1370
1761-2 E3130 Note: If active 1761 diagnostic codes are present, this may be due to an issue with the DEF pump which is causing a loss of prime. Operate the machine for several minutes and check to see if the DEF levels recoverNote: Troubleshoot any electrical diagnostic codes associated with the DEF header or CAN C data link before performing the procedure detailed below.Complete the procedure in the order in which the steps are listed.Note: Before starting the troubleshooting steps, please ensure that the DEF system (including tank and lines) is fully thawed and is at least half full of DEF
Table 3
Troubleshooting Test Steps Values Results
1. Check that the latest available software is installed and there are no applicable Technical Information Bulletins or Special Instruction documentation released
A. Ensure that the latest software is installed on the engine ECM.
B. Ensure that the latest software is installed on the Dosing Control Unit (DCU)
If necessary, refer to Troubleshooting, "ECM Software - Install" for the correct procedure.
C. Ensure all Technical Information Bulletins and/or Special Instruction documented for the issue and/or product are reviewed and followed.
Software and Publications
Result: The latest software is not installed.
Repair: Install the latest engine ECM software and then install the latest DCU software. If necessary, refer to Troubleshooting, "ECM Software - Install" for the correct procedure.
Start the engine and wait for 2 minutes.
If the fault is cleared, return the engine to service.
If the fault is still present, proceed to Test Step 2.
Result: Applicable Technical Information Bulletin/Special Instruction publication is available.
Repair: Review and follow instructions provided in the available publication.
Result: The latest software is installed.
Proceed to Test Step 2.
2. Check the DEF Fluid Level
A. Turn the keyswitch to the ON position. Do not start the engine.
B. Check the current position of the DEF gauge.
Note: The gauge may take up to 60 seconds to show the correct DEF level.
C. Turn the keyswitch to the OFF position.
D. Clean dirt and debris from around the cap before removing the cap.
E. Add DEF to the DEF tank.
Note: Only use DEF that meets ISO 22241 quality standards.
F. Turn the keyswitch to the ON position.
Note: The gauge may take up to 60 seconds to show the correct DEF level.
G. Check for a change in the gauge position.
Gauge position
Result: The gauge did not move by adding DEF to the tank.
Proceed to Test Step 3.
Result: The gauge moved by adding DEF to the tank.
Turn the keyswitch to the OFF position until the "Wait to Disconnect" lamp switches off to allow the DEF pump to purge, reset the code, and reset the DEF Control Unit (DCU). Return the unit to service.
Illustration 1 g03700612
(1) DEF tank header electrical connector
(2) DEF tank header
Table 4
Troubleshooting Test Steps Values Results
3. Check the Electrical Connection at the DEF Tank Header
A. Inspect electrical connector (1) to the DEF tank header. Refer to Troubleshooting, "Electrical Connectors - Inspect".
Check for corrosion or loose wires.
Electrical connections
Result: The electrical connectors are free of corrosion and are not loose.
Proceed to Test Step 4.
Result: The electrical connections are corroded and/or loose.
Repair: Make the necessary repairs to the connectors. Turn the keyswitch to the OFF position until the "Wait to Disconnect" lamp switches off to allow the DEF pump to purge, reset the code, and reset the Dosing Control Unit (DCU).
Use the electronic service tool to perform the "Aftertreatment System Functional Test" to ensure that the repair eliminates the fault.
Repeat this procedure from Test Step 1.
4. Check the DEF Level Measurement
A. Operate the machine to agitate the DEF in the tank
Gauge position
Result: The gauge did not move.
Repair : Repair the DEF Tank header sensor with the DEF Manifold Sensor Kit. Refer to Disassembly and Assembly, Manifold (DEF Heater) Sensor - Disassemble (Temperature, Level, Quality DEF Manifold Sensor) and Manifold (DEF Heater) Sensor -Assemble (Temperature, Level, Quality DEF Manifold Sensor).
Result: The gauge moved.
Proceed to Test Step 5.
5. Inspect the DEF Tank Header
A. Turn the keyswitch to the OFF position.
B. Remove tank header (2) from the DEF tank. Refer to the Disassembly and Assembly manual for the correct procedure..
C. Inspect the DEF tank header for damage and check for a stuck float.
Proper operation of the float
Result: The float was not operating correctly.
Repair: Repair the float if possible. If the float cannot be repaired, replace the DEF tank header. Refer to the Disassembly and Assembly manual for the correct procedure.
Return the unit to service.
Result: The float was operating correctly.
Repair : Repair the DEF Tank header sensor with the DEF Manifold Sensor Kit. Refer to Disassembly and Assembly, Manifold (DEF Heater) Sensor - Disassemble (Temperature, Level, Quality DEF Manifold Sensor) and Manifold (DEF Heater) Sensor -Assemble (Temperature, Level, Quality DEF Manifold Sensor).
Return the unit to service.
If the procedure did not correct the issue, contact the Dealer Solutions Network (DSN).


Parts cylinder JOHNSON:

0394601
 
0394601 CYLINDER ASSY., Tilt
BJ250CXECB, BJ250CXEDA, BJ250CXEUM, CJ275TLCOS, CJ300TLCOS, J250CXARC, J250CXEIE, J250CXEND, J250CXEOR, J275CLCUR, J275CXCCA, J300CLCUR, J300CXCCA, J300CXCEM, J300CXEIE, J300CXEND, J300CXEOR, J300CXERC, J300CXESB
0913331
 
0913331 CYLINDER, Starboard
BJ250CXEDA, BJ250CXEUM, J185ESXESS, J185ESXW, J200CXCCR, J200CXCEA, J200CXESM, J225CXCCE, J225CXCED, J225CXESS, J250CXARC, J250CXATF, J250CXEIE, J250CXEND, J250CXEOR, J275CXCCA, J300CXCCA, J300CXCEM, J300CXEIE, J300CXEND, J300CXEOR, J300CXERC, J300CX
0985526
 
0985526 CYLINDER & VALVE ASSY.
J185ESXESS, J185ESXW, J200CXCCR, J200CXCEA, J200CXESM, J225CXCCE, J225CXCED, J225CXESS, J275CXCCA, J300CXCCA, J300CXCEM, J300CXESB
0398717
 
0398717 CYLINDER HEAD
J250CXATF, J250CXEIE, J250CXEND, J275CXCCA, J300CXCCA, J300CXCEM, J300CXEIE, J300CXEND, J300CXESB, J300CXETF
0431635
 
0431635 CYLINDER HEAD
J275CXCCA, J300CXCCA
0434502
 
0434502 CYLINDER & C
J250CXEIE, J300CXEIE
0987052
 
0987052 CYLINDER & VALVE ASSY.
BJ250CXEDA, BJ250CXEUM, J250CXARC, J250CXATF, J250CXEIE, J250CXEND, J250CXEOR, J300CXEIE, J300CXEND, J300CXEOR, J300CXERC, J300CXETF
0435719
 
0435719 CYLINDER & C'CASE ASSY., 250
J250CXATF, J250CXEND, J300CXEND, J300CXETF
Back to top