0312690 JOHNSON DASH PANEL


0312690 DASH PANEL JOHNSON 25E72R, 25E73A, 25E74M, 25E75B, 25E76E, 25E77S, 33E69A, 33E69A, 33E70M, 33E70M, 35E76G, 35E77C, 40E71B, 40E72E, 40E73D, 40E74S, 40E75C, 40E76A, RX-16M DASH
0312690 DASH PANEL JOHNSON
Rating:
53

Buy DASH PANEL 0312690 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 18
 

BRP JOHNSON entire parts catalog list:

25E72R, 25EL72R, 25R72R, 25RL72R 1972
25E73A, 25EL73A, 25R73A, 25RL73A 1973
25E74M, 25EL74M, 25R74M, 25RL74M 1974
25E75B, 25EL75B, 25R75B, 25RL75B 1975
25E76E, 25EL76E, 25R76E, 25RL76E 1976
25E77S, 25EL77H, 25EL77S, 25R77H, 25R77S, 25RL77H, 25RL77S 1977
33E69A, 33EL69A, 33R69A, 33RL69A 1969
33E69A, 33EL69A, 33R69A, 33RL69A 1969
33E70M, 33EL70M, 33R70M, 33RL70M 1970
33E70M, 33EL70M, 33R70M, 33RL70M 1970
35E76G, 35E76S, 35EL76G, 35EL76S, 35R76G, 35R76S, 35RL76G, 35RL76S 1976
35E77C, 35E77H, 35EL77C, 35EL77H, 35R77C, 35R77H, 35RL77C, 35RL77H 1977
40E71B, 40E71G, 40EL71B, 40EL71G, 40R71B, 40R71G, 40RL71B, 40RL71G 1971
40E72E, 40EL72E, 40R72E, 40RL72E 1972
40E73D, 40EL73D, 40R73D, 40RL73D 1973
40E74S, 40EL74S, 40R74S, 40RL74S 1974
40E75C, 40EL75C, 40R75C, 40RL75C 1975
40E76A, 40E76R, 40EL76A, 40EL76R, 40R76A, 40R76R, 40RL76A, 40RL76R 1976
RX-16M, RX-16R, RXE-16M, RXE-16R, RXEL-16M, RXEL-16R, RXL-16M, RXL-16R 1968

Information:


Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
If the fuel system runs out of fuel, or if air is introduced into the fuel system, the following procedure may be followed.
Turn the ignition switch to the "OFF" position.
Fill the fuel tank with clean diesel fuel.
Illustration 1 g01927544
Illustration 2 g01927558
View of area A
(1) Fuel regulator valve
(2) Fuel return line from cylinder head
(3) Air purge
Illustration 3 g01927569
(4) Fuel priming pump
Turn the priming valve (If Equipped) to the "Closed (Prime)" position in order to prime the fuel system.
Purging air from the fuel system requires the air purge to be opened three full turns. Open air purge (3). Do not remove the screw.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Crank the engine for 30 seconds. Use a suitable container to catch the fuel while you crank the engine. Allow the starting motor to cool for 2 minutes. Note: Most of the air should be purged from the system after four or five cranking cycles.
Repeat Step 5 until the engine starts and runs. If the engine runs rough, continue to operate the engine at low idle until the engine runs smoothly.
Observe air purge (3). When a small drop of fuel appears at the threads of the air purge, close and tighten air purge (3). Note: Failure to tighten all fittings could result in serious fuel leaks.
After the engine has operated smoothly for 30 seconds, turn the priming valve to the "Open (Run)" position. Note: Shortened injector life may occur if the priming valve is left in the "Closed (Prime)" position.
Clean any residual fuel from the engine components.
Once the engine runs smoothly, stop the engine. Turn the ignition switch to the OFF position. Note: You may use the hand priming pump for the fuel filter (if equipped) instead of cranking the engine and running the engine. Perform the following procedure when the hand priming pump is used:
Illustration 4 g01451302
(1) Fuel priming pump
(2) Air purge
(3) Priming valve (If Equipped)
Turn the priming valve (3) (If Equipped) to the "Closed (Prime)" position in order to prime the fuel system.
Purging air from the fuel system requires the air purge (2) for the fuel filter to be opened three full turns. Open air purge (2). Do not remove the screw.
While you operate the hand priming pump, observe the air purge (2). When a small drop of fuel appears at the threads of the air purge, close and tighten the air purge (2). Note: Failure to tighten all fittings could result in serious fuel leaks.
Clean any residual fuel from the engine components.
Continue to operate the fuel priming pump (1) until a strong resistance is felt. Listen for an audible click from the fuel manifold. The click will indicate that the valve has opened and the fuel system is pressurized. Lock the fuel priming pump.
Do not crank the engine for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking again.
Crank the engine. If the engine starts but the engine runs rough, continue to operate the engine at low idle until the engine runs smoothly. Note: If the engine will not start, further priming is necessary. If the engine starts but the engine continues to misfire or smoke, further priming is necessary.
After the engine has operated smoothly for 30 seconds, turn the priming valve (3) to the "Open (Run)" position. Note: Shortened injector life may occur if the priming valve (3) is left in the "Closed (Prime)" position.


Back to top