0210666 JOHNSON DECAL, Evinrude only

Table 1
Configuration Parameters for G3600 Engines
ECM Identification Parameters
"Equipment ID"
"Engine Serial Number"
"ECM Serial Number"
"Software Group Part Number"
"Software Group Release Date"
"Software Group Description"
Selected Engine Rating
"Rating Number"
Timing Control
"First Desired Timing"
Gaseous Fuel Parameters
"Fuel Quality Input Type Configuration"
"Fuel Quality"
"Fuel Quality Sensor LHV Lower Setpoint"
"Fuel Quality Sensor LHV Upper Setpoint"
"Gas Specific Gravity"
"Fuel Specific Heat Ratio"
Air/Fuel Ratio Control
"Emissions Feedback Mode Configuration"
"Desired Engine Exhaust NOx Level Setting"
"Maximum Choke Position"
"Engine Start Choke Position"
"Ignition Multi Strike Feature Enable"
"Ignition Multi Strike Mode Configuration"
"Ignition Multi Strike Engine Startup Activation Duration"
Speed Control
"Desired Speed Input Configuration"
"Secondary Desired Speed Input Configuration"
"Low Idle Speed"
"Engine Acceleration Rate"
"Maximum Engine High Idle Speed"
"Minimum Engine High Idle Speed"
"Governor Type Setting"
"Engine Speed Droop"
Governor Gain Parameters
"Governor (Proportional) Gain Percentage"
"Governor (Integral) Stability Percentage"
Engine State Control
"Engine State Control Input Configuration"
"Engine State Control Secondary Input Configuration"
"Engine State Control Default Value"
"Starting System #1 Type"
"Starting System #2 Type"
"Crank Terminate RPM"
"Engine Purge Cycle Time"
"Crank Duration"
"Cycle Crank Time"
"Engine Speed Drop Time"
"Cooldown Duration"
"Driven Equipment Delay Time"
Engine Prelubrication
"Engine Post-Lube Duration"
"Engine Ready to Start Pre-lube Duration"
Monitoring and Protection
"Engine Post-Lube Duration"
"High Inlet Air Temperature Engine Load Set Point"
Security Access Parameters
"Customer Password #1"
"Customer Password #2"
"Total Tattletale" Information for the ECM
"Equipment ID"
The customer can assign an "Equipment ID" for identification."Engine Serial Number"
The engine serial number is programmed into the ECM at the factory. The number is stamped on the engine Information Plate."ECM Serial Number"
The ECM serial number is programmed into the ECM at the factory."Software Group Part Number"
Part number of the flash file that is currently installed in the ECM."Software Group Release Date"
Release date of the flash file that is currently installed in the ECM."Software Group Description"
Description of the application for the flash file that is currently installed in the ECM.Selected Engine Rating
"Rating Number"
The "Rating Number" is a factory password protected parameter that will control the engine rated power trim. The available options for this rating number parameter are 1, 2 or 3. Each rating number represents a SCAC temperature rating. Parameter 1 means 54° C SCAC, parameter 2 means 43° C and parameter 3 means 32° C. The lower the SCAC temperature means the higher the power output. This parameter is set to the purchased rating from the factory.Timing Control
"First Desired Timing"
The "First Desired Timing" is determined with the methane number of the primary fuel that is used. Use the Engine Performance Sheet, "Fuel Usage Guide".Note: Determine the desired timing by using the Caterpillar Software, LERW4485, "Gas Engine Rating Pro (GERP)" with the results that are from the fuel analysis. Use of only the data from the gas analysis can result in incorrect settings.Gaseous Fuel Parameters
"Fuel Quality Input Type Configuration"
This parameter is used to select the type of Lower Heating Value (LHV) input. The default setting is"Configured Value". This setting is used when the LHV input is set by the operator in ET. Select the"4 to 20 mA" setting when a gas chromatograph uses 4 to 20 mA to represent the LHV of the fuel. This setting is most often used in landfill applications."Fuel Quality"
This parameter is programmed to the Lower Heating Value (LHV) of the primary fuel. The fuel ratio control of the ECM will compensate for some inaccuracy in this setting. The ECM assumes a corrected value that is equal to the customer programmed "Fuel Energy Content" that is multiplied by the "Fuel Correction Factor". This factor is displayed on the Cat ET screen. An event code is generated if the "Fuel Correction Factor" exceeds a limit that is programmed at the factory. The event code will indicate the need to reprogram this value. Obtain a gas analysis in order for this parameter to be accurately programmed."Fuel Quality Sensor L