0346480 JOHNSON *DECAL, Rear - V,U


0346480 *DECAL, Rear - V,U JOHNSON BJ115PLSSB, BJ90PLSSE DECAL
0346480 *DECAL, Rear - V,U JOHNSON
Rating:
98

Buy *DECAL, Rear - V,U 0346480 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 17
 

Compatible models:

BRP JOHNSON entire parts catalog list:

BJ115PLSSB, BJ115PXSSB, BJ115VXSSS, J115JPLSSR, J115PLSSB, J115PXSSB, J115SPLSSC, J115VLSSS, J115VXSSS, RJ115PLSSB, RJ115PXSSB, RJ115VLSSB, RJ115VXSSS 2000
BJ90PLSSE, BJ90PXSSE, BJ90VXSSS, J90PLSSE, J90SPLSSC, J90VLSSE, RJ90PLSSE, RJ90VLSSS 2000

Information:


Illustration 1 g00997504
C-10 and C -12 low oil pressure
Illustration 2 g00997505
3406E, C-15, C-16, and C-18 low oil pressureSystem Response:The Caterpillar Electronic Technician (Cat ET) will display "LOW OIL PRESSURE" and "DIAG" next to the status for "Engine Oil Pressure". The check engine lamp and the warning lamp will illuminate.Customer passwords are required to clear this diagnostic code.NoneTest Step 1. Check the Engine Oil Level
Check the engine oil level.Expected Result:The engine oil level is OK.Results:
OK - The engine oil level is OK. Proceed to Test Step 2.
Not OK - The engine oil level is low.Repair: Add engine oil to the proper level. Refer to the Operation and Maintenance Manual for more information.STOPTest Step 2. Verify Proper Sensor Installation
Check the installation of the engine oil pressure sensor.
Check the wiring of the engine oil pressure sensor. Refer to the Electrical Schematic for the proper wiring. Ensure that all of the wires and connectors are properly connected.Expected Result:The sensor is properly installed and the wiring is correct.Results:
OK - The sensor is properly installed. Proceed to Test Step 3.
Not OK - The sensor is not installed properly.Repair: Install the engine oil pressure sensor properly. Repair the wiring and/or the connectors to the sensor.Verify that the repair eliminates the problem.STOPTest Step 3. Check for Active Diagnostic Codes
Connect Cat ET to the data link connector.
Check for active diagnostic codes that are related to the barometric pressure sensor (atmospheric pressure) or the boost pressure sensor.Expected Result:There are no diagnostic codes that are related to the barometric pressure sensor (atmospheric pressure) or the boost pressure sensor.Results:
OK - There are no diagnostic codes. Proceed to Test Step 4.
Not OK - There is a diagnostic code that is related to the barometric pressure sensor (atmospheric pressure) and/or the boost pressure sensor.Repair: Troubleshoot the diagnostic code before continuing with this procedure.STOPTest Step 4. Check the Status Screen
Turn the key switch to the ON position. The engine should be off.
Monitor the status for "Boost Pressure" and "Engine Oil Pressure" on Cat ET.Expected Result:"Boost Pressure" and "Engine Oil Pressure" should be less than 10 kPa (2 psi).Results:
OK - The boost pressure and the engine oil pressure are less than 10 kPa (2 psi). Proceed to Test Step 6.
Not OK - Boost Pressure - The boost pressure is greater than 10 kPa (2 psi). Proceed to Test Step 8.
Not OK - Engine Oil Pressure - The engine oil pressure is greater than 10 kPa (2 psi). Proceed to Test Step 9.
Not OK - Both - The boost pressure and the engine oil pressure are greater than 10 kPa (2 psi). Proceed to Test Step 5.Test Step 5. Check the


Parts decal JOHNSON:

0346690
 
0346690 *DECAL, Rear - Z
BJ115PLSSB, BJ90PLSSE
0346696
 
0346696 *DECAL, Rear - T
BJ115PLSSB, BJ90PLSSE
0346475
 
0346475 *DECAL, Rear - Y,X
BJ115PLSSB, BJ90PLSSE
0346706
 
0346706 *DECAL, Sides - Z,W,T
BJ115PLSSB, BJ90PLSSE
0346476
 
0346476 *DECAL, Sides -Y,X,V,U
BJ115PLSSB, BJ90PLSSE
0346695
 
0346695 *DECAL, Front - T
BJ115PLSSB, BJ90PLSSE
0346477
 
0346477 *DECAL, Front - Y,X
BJ115PLSSB, BJ90PLSSE
0346481
 
0346481 *DECAL, Front - V,U
BJ115PLSSB, BJ90PLSSE
Back to top