0348683 JOHNSON *DECAL, Rear, 200


0348683 *DECAL, Rear, 200 JOHNSON BJ200PLSIF, BJ225PLSIF, J200WPXSIF, J225HPLSIF, J250VCZSIF DECAL
0348683 *DECAL, Rear, 200 JOHNSON
Rating:
88

Buy *DECAL, Rear, 200 0348683 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 12
 

BRP JOHNSON entire parts catalog list:

BJ200PLSIF, BJ200VCSIF, BJ200VXSIF, J200PLSIF, J200VCXSIF, J200VLSIF, J200VXSIF, RJ200PLSIF, RJ200VXSIF 2001
BJ225PLSIF, BJ225VCSIF, BJ225VXSIF, J225HGLSIF, J225HPLSIF, J225PLSIF, J225VCXSIF, J225VLSIF, J225VXSIF, RJ225CXSIF, RJ225HLSIF, RJ225PLSIF, RJ225VXSIF 2001
J200WPXSIF 2001
J225HPLSIF 2001
J250VCZSIF, J250VXSIF, J250VZSSIF, RJ250VXSIF, RJ250VZSSIF 2001

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.Refer to Systems Operation, Testing and Adjusting Manual, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all hoses, on all hose assemblies, on wires and on all tube assemblies for installation purposes. Plug all hose assemblies and tube assemblies. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Turn the fuel supply to the OFF position.
If necessary, remove the boost pressure sensor. Refer to Disassembly and Assembly, "Boost Pressure Sensor - Remove and Install".
Illustration 1 g01247416
Typical example
Disconnect plastic tube assemblies (3), (5) and (6) from fuel filter base (1). Note: If the tube assemblies have quick fit connections, ensure that the connections are clean before the tube assemblies are plugged.
Remove tube assembly (4), if equipped.
Use Tooling (A) in order to remove fuel filter (7). Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace".
Remove bolts (2) from fuel filter base (1). Remove the fuel filter base from the cylinder head. Note: Do not attempt to disassemble the fuel filter base.Installation Procedure
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.Refer to Systems Operation, Testing and Adjusting Manual, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Ensure that the fuel filter base is clean and free from damage. If necessary, replace the complete fuel filter base assembly.
Illustration 2 g01247416
Typical example
Position fuel filter base (1) onto the cylinder head. Install bolts (2). Tighten the bolts to a torque of 22 N m (16 lb ft).
Install a new fuel filter (7) to fuel filter base (1). Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
If necessary, install the boost pressure sensor. Refer to Disassembly and Assembly, "Boost Pressure Sensor - Remove and Install".
Install tube assembly (4), if equipped. Tighten the nuts to a torque of 9 N m (80 lb in).
Ensure that the plastic tube assemblies are installed in the original positions. Failure to connect the plastic tube assemblies to the correct ports will allow contamination to enter the fuel system. Contaminated fuel will cause serious damage to the engine.
Connect plastic tube assemblies (3), (5) and (6) to fuel filter base (1). Note: If the tube assemblies have quick fit connections, ensure that the connections are clean before the tube assemblies are connected.
Turn the fuel supply to the ON position.
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime".


Parts decal JOHNSON:

0348690
 
0348690 *DECAL, Front
BJ135PLSIF, BJ200PLSIF, BJ225PLSIF, J200WPXSIF, J225HPLSIF, J250VCZSIF
0349480
 
0349480 *DECAL, Front, 225 HO
BJ200PLSIF, BJ225PLSIF, J225HPLSIF, J250VCZSIF
0348623
 
0348623 *DECAL, Front, 225 HO
BJ200PLSIF, BJ225PLSIF, J225HPLSIF, J250VCZSIF
0348688
 
0348688 *DECAL, Wrap
BJ135PLSIF, BJ200PLSIF, BJ225PLSIF, J200WPXSIF, J225HPLSIF, J250VCZSIF
0348691
 
0348691 *DECAL, Rear, 250
BJ200PLSIF, BJ225PLSIF, J225HPLSIF, J250VCZSIF
0348685
 
0348685 *DECAL, Rear, 225
BJ200PLSIF, BJ225PLSIF, J225HPLSIF, J250VCZSIF
0348619
 
0348619 DECAL, Ocean pro
BJ135PLSIF, BJ200PLSIF, BJ225PLSIF, J225HPLSIF, J250VCZSIF
0348627
 
0348627 DECAL, Commercial
BJ200PLSIF, BJ225PLSIF, J200WPXSIF, J225HPLSIF, J250VCZSIF
Back to top