0350294 JOHNSON DECAL, Stbd


0350294 DECAL, Stbd JOHNSON BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, J10RLSUR, J15RLSDR, J15RLSOC, J15RLSRS, J15RLSTD, J15RLSUA, J6R4SRC, J6R4STS, J6RLSOC, J6RLSRS, J6RLSTD, J8R4SRC, J8R4STS, J8RLSOR, J8RLSRC, J8RLSTS DECAL
0350294 DECAL, Stbd JOHNSON
Rating:
58

Buy DECAL, Stbd 0350294 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

BRP JOHNSON entire parts catalog list:

BJ10RHLSDA, BJ10RHSDA, J10RLSDC, J10RSDC 2006
BJ10RHLSOR, BJ10RHSOR, J10RLSOS, J10RSOS 2005
BJ10RHLSRC, BJ10RHSRC, J10RLSRD, J10RSRD 2004
BJ10RHLSTS, BJ10RHSTS, J10RLSTE, J10RSTE 2003
J10RLSUR, J10RSUR 2007
J15RLSDR, J15RSDR, J15RTSDC 2006
J15RLSOC, J15RSOC, J15RTSOS, J15WRLSOB, J15WRSOB 2005
J15RLSRS, J15RSRS, J15WRLSRM, J15WRSRM 2004
J15RLSTD, J15RSTD 2003
J15RLSUA, J15RSUA, J15RTSUR 2007
J6R4SRC, J6RL4SRC 2004
J6R4STS, J6RL4STS 2003
J6RLSOC, J6RSOC 2005
J6RLSRS, J6RSRS 2004
J6RLSTD, J6RSTD 2003
J8R4SRC, J8RL4SRC 2004
J8R4STS, J8RL4STS 2003
J8RLSOR, J8RSOR 2005
J8RLSRC, J8RSRC 2004
J8RLSTS, J8RSTD 2003

Information:

Introduction
There have been isolated instances of issues with 353-3571 Filter Tube that are installed on certain C6.6 machine engines.
Do not perform any procedure that is outlined in this Special Instruction until you have read and understood the information that is contained in this document.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training. Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, General Hazard Information and High Pressure Fuel Lines for safety information. Refer to System Operation, Testing and Adjusting, Cleanliness of Fuel System Components for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Required Parts
Table 1
Required Parts    
Part Number     Part Description     Qty    
439-8115     Fuel Line     1    Removal Procedure
Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     278-4138     Fuel System Protection Gp     1    
Illustration 1 g03646083
Tube assembly with plastic section incorporated between the two steel sections
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
Illustration 2 g03722979
Typical example
Illustration 3 g03722980
Typical example
Remove bolt (1) from the clip for tube assembly (6) .
Remove nut (3) from the clip for tube assembly (6). Remove nut (2) from bolt (8) .
If necessary, disconnect fuel injection line at fuel injection pump in order to improves access. Use Tooling (A) in order to plug the open port in fuel injection pump.
Remove tube assembly (6) from fuel injection pump (16) and secondary fuel filer assembly (5) .
Use Tooling (A) to cap the connection on secondary fuel filer assembly (5). Use Tooling (A) to cap the connection (15) on fuel injection pump.
Disconnect tube assembly (9) from secondary fuel filer assembly (5) .
Use Tooling (A) to cap the connection on secondary fuel filer assembly (5). Use Tooling (A) to plug the tube assembly (9) .
Disconnect tube assembly (7) from secondary fuel filer assembly (5) .
Use Tooling (A) to cap the connection on secondary fuel filer assembly (5). Use Tooling (A) to plug the tube assembly (7) .
Remove bolt (11) from bracket (10). Remove spacer (12). Remove bracket (10). Remove tube assembly (7) from clip (17) .
Remove bolts (8) for secondary fuel filer assembly (5). Remove spacer (4) from bracket (14). Remove secondary fuel filer assembly (5) .
Remove bolts (13) from bracket (14). Remove bracket (14) .Installation Procedure
Illustration 4 g03646163
Typical example
Remove the plug from the fuel connection. Install the new 439-8115 Fuel Line (1) to fuel connection (2). Orientate the tube assembly such that the fourth leg at Position (X) is vertical. Refer to illustration 4. Tighten the tube nut finger tight.
Illustration 5 g03646171
Typical example
Position bracket (4) onto the cover of the inlet manifold.
Install 6I-0260 Bolts (3) to the bracket (4). Tighten the bolts to a torque of 22 N m (195 lb in).
Illustration 6 g03645420
Typical example
Position the bracket (5) onto bracket (4) .
Install nuts (6). Tighten the nuts to a torque of 44 N m (32 lb ft).
Install bolt (7) finger tight.


Parts decal JOHNSON:

0350293
 
0350293 DECAL, "JOHNSON"-Port/Stbd
BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, J10RLSUR, J15RLSDR, J15RLSOC, J15RLSRS, J15RLSTD, J15RLSUA, J6R4SRC, J6R4STS, J6RLSOC, J6RLSRS, J6RLSTD, J8R4SRC, J8R4STS, J8RLSOR, J8RLSRC, J8RLSTS
0350295
 
0350295 DECAL, Port
BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, J10RLSUR, J15RLSDR, J15RLSOC, J15RLSRS, J15RLSTD, J15RLSUA, J6R4SRC, J6R4STS, J6RLSOC, J6RLSRS, J6RLSTD, J8R4SRC, J8R4STS, J8RLSOR, J8RLSRC, J8RLSTS
0350296
 
0350296 DECAL, 4 STROKE-Port & Stbd
J6R4SRC, J6R4STS, J8R4SRC, J8R4STS
0350297
 
0350297 DECAL, "BOMBARDIER" - Front
BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, J15RLSOC, J15RLSRS, J15RLSTD, J6R4SRC, J6R4STS, J6RLSOC, J6RLSRS, J6RLSTD, J8R4SRC, J8R4STS, J8RLSOR, J8RLSRC, J8RLSTS
0350298
 
0350298 DECAL, "JOHNSON" - Rear
BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, J10RLSUR, J15RLSDR, J15RLSOC, J15RLSRS, J15RLSTD, J15RLSUA, J6R4SRC, J6R4STS, J6RLSOC, J6RLSRS, J6RLSTD, J8R4SRC, J8R4STS, J8RLSOR, J8RLSRC, J8RLSTS
0350300
 
0350300 DECAL, 6 HP - Rear
J6R4SRC, J6R4STS, J6RLSOC, J6RLSRS, J6RLSTD, J8RLSOR, J8RLSRC, J8RLSTS
0350302
 
0350302 DECAL, "Johnson" - Front
J6RLSOC, J6RLSRS, J6RLSTD, J8R4SRC, J8R4STS, J8RLSOR, J8RLSRC, J8RLSTS
0350301
 
0350301 DECAL, "8.0" - Rear
J6RLSOC, J6RLSRS, J6RLSTD, J8R4SRC, J8R4STS, J8RLSOR, J8RLSRC, J8RLSTS
Back to top