0398974 DECAL SET JOHNSON
J10ECCD, J10ECUE, J15ECCS, J15ECUD
DECAL
Price: query
Rating:
BRP JOHNSON entire parts catalog list:
- ENGINE COVER - JOHNSON » 0398974
J15ECCS, J15ELCCS, J15RCCS, J15RLCCS 1988
J15ECUD, J15ELCUD, J15RCUD, J15RLCUD 1987
Information:
Table 1
J1939 Code and Description CDL Code and Description Comments
98-1
Engine Oil Level : Low - most severe (3) E171 (3)
Low Engine Oil Level The ECM may derate the engine or shutdown the engine.
The code is logged.
98-17
Engine Oil Level : Low - least severe (1) E171 (1)
Low Engine Oil Level The ECM may derate the engine or shutdown the engine.
The code is logged.
98-18
Engine Oil Level : Low - moderate severity (2) E171 (2)
Low Engine Oil Level The ECM may derate the engine or shutdown the engine.
The code is logged.
Illustration 1 g06309502
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Look for active codes that are associated with the system for the event code.
Codes
Result: An associated code is active.
Repair: Troubleshoot any associated codes before continuing with this test.
Result: A code is active or logged.
Proceed to Test Step 2.
2. Check the Engine Oil Level
Oil Level
Result: The engine oil is at the proper level.
Proceed to Test Step 3.
Result: The engine oil level is low.
Repair: Add engine oil in order to obtain the correct engine oil level. Refer to Operation and Maintenance Manual, "Engine Oil" for the recommendations of engine oil.
Start the engine. Inspect the exterior of the engine for oil leaks. Repair any oil leaks.
If the problem is not resolved, proceed to Test Step 3.
3. Check the Supply Voltage at the Oil Level Sensor Connector
A. Disconnect the oil level sensor at the sensor connector.
B. Restore electrical power to the ECM.
C. Measure the voltage between the following wiring harness connector terminals for the oil level sensor:
- Terminal A (sensor supply) and Terminal B (sensor return)
D. Remove electrical power from the ECM.
5.0 0.2 VDC
Result: The voltage measurement is 5.0 0.2 VDC. The supply voltage is reaching the sensor.
Proceed to Test Step 4.
Result: The voltage measurement is not 5.0 0.2 VDC.
Repair: The sensor supply voltage is not reaching the sensor. There is a problem in the circuit for the sensor supply. Repair the wiring harness between the sensor and the ECM.
If the problem is not resolved, proceed to Test Step 4.
4. Short the Signal Wire to Ground on the Oil Level Sensor
A. Fabricate a jumper wire that is long enough to create a short circuit between two terminals at the oil level sensor harness connector. Crimp connector pins to each end of the jumper wire.
B. Install the jumper wire between the following wiring harness connector terminals for the oil level sensor:
- Terminal B (sensor return) and Terminal C (sensor signal)
C. Connect Cat ET.
D. Use Cat ET to monitor the status of the "Oil Level".
E. Remove the jumper wire. Connect the harness connector for the oil level sensor.
5 VDC
Result: The status changes when the jumper wire is installed.
Repair: Replace the failed oil level sensor.
Verify that the repair eliminated the problem.
Result: The status does not change when the jumper wire is installed.
Repair: The problem is between the ECM and the sensor connector. Repair the wiring harness.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Parts decal JOHNSON:
0283332
0283333
0283345
0398973
0398992
0210660
0210660 DECAL, Exhaust hsg., Ev.
J10ECCD, J10ECUE, J15ECCS, J15ECUD, J20CRCCA, J20CRCUR, J25ECCM, J25ECUA, J30ECCE, J35RCCE
0332635
0332635 DECAL, Exhaust hsg., Jo.
J10ECCD, J10ECES, J10ECUE, J10EESC, J15ECCS, J15ECEC, J15ECUD, J15EESR, J20CRCCA, J20CRCEM, J20CRCUR, J20CRESB, J20ECEM, J20EESB, J25ECCM, J25ECEB, J25ECUA, J25EESE, J25RCEM, J25RESB, J25TECEM, J25TEESB, J30ECCE, J30ECED, J30EESS, J30RCED, J30RESS, J