0435359 JOHNSON DECAL SET, 90, 115


0435359 DECAL SET, 90, 115 JOHNSON J100STLEIE, J100STLEND, J100STLETS, J115JLEIE, J115JLEND, J115JLETS, J88MSLEIM, J88MSLEIM, J88MSLENB, J88MSLENB, J88MSLETE, J88MSLETE DECAL

Buy DECAL SET, 90, 115 0435359 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 25
 

BRP JOHNSON entire parts catalog list:

J100STLEIE, VJ100SLEIE 1991
J100STLEND, VJ100SLEND 1992
J100STLETS, VJ100SLETS 1993
J115JLEIE, J115MLEIE, J115TLAIE, J115TLEIE, J115TXEIE, TJ115TLEIE, VJ115TLAIE, VJ115TLEIE, VJ115TXEIE 1991
J115JLEND, J115MLEND, J115TLAND, J115TLEND, J115TXEND, TJ115TLEND, VJ115TLAND 1992
J115JLETS, J115MLETS, J115TLATS, J115TLETS, J115TXATS, TJ115TLETS, VJ115TLATS, VJ115TLETS 1993
J88MSLEIM 1991
J88MSLEIM, J90JLEIE, J90TLAIE, J90TLEIE, TJ90TLEIE, VJ90MLEIE, VJ90TLAIE, VJ90TLEIE 1991
J88MSLENB 1992
J88MSLENB, J90JLEND, J90TLAND, J90TLEND, TJ90TLEND, VJ90MLEND, VJ90TLAND, VJ90TLEND 1992
J88MSLETE 1993
J88MSLETE, J90JLETS, J90TLATS, J90TLETS, J90TXATS, TJ90TLETS, VJ90MLETS, VJ90TLATS, VJ90TLETS 1993

Information:

The oil supply oil tube does not have to be loosened in order to remove the rocker shaft assembly & push rods.1. Remove three nuts (1) and bolt (2) evenly and gradually. Begin with the end brackets and move towards the center. When installing, aluminum bracket nuts and bolt are tighten evenly and gradually beginning with the inner fasteners and working towards the end fasteners to a torque of 40 N m (30 lb ft). Cast iron brackets are tighten evenly and gradually beginning with the inner fasteners and working towards the end fasteners to a torque of 75 N m (55 lb ft). Lubricate the nuts and bolt with clean engine oil before installing.2. Remove rocker shaft assembly (3).3. Remove the oil seal from the oil supply connection or the oil supply hole in the cylinder head. When installing, replace with a new oil seal. 4. Remove four or six push rods (4). Mark or identify for later installation. When installing, make sure the push rods fit correctly into the sockets of the tappets. When installing, make sure the oil supply connection fits correctly into the new oil seal. When installing, make sure the ends of the adjustment screws fit into the sockets of the push rods. For installation of the rocker shaft assembly and push rods, reverse the removal steps.End By:a. install valve coverDisassemble & Assemble Rocker Shaft Assembly
Start By:a. remove rocker shaft assembly 1. Use a screw driver or similar tool to remove retaining ring (1) from each end of the rocker shaft assembly.2. Slide the components off each end of the rocker shaft assembly. Mark or identify each component as to their location and position for later assembly.
Retaining Ring (1). Shaft End Washer (2). Lever Assembly (3). Shaft Bracket (4). Shaft Spring (5). Washer (6). Rocker Shaft (7).3. Rocker shaft assembly completely disassembled. Clean and inspect all rocker shaft assembly components. Check the clearance of the rocker levers on the rocker shaft. If the clearance is more than 0.13 mm (0.0005 inch). Replace the rocker lever bushing and/or the rocker shaft.
Use Tool (A) and a suitable press to remove rocker lever bushing (10) if necessary. Make sure the lubrication hole on the new bushing is in line with the hole in the rocker lever when installing bushing. Ream the bushing to permit a clearance of 0.03 to 0.09 mm (0.001 to 0.004 inch).
4. If necessary, remove bolt (8) and oil supply connection (9) from the rocker shaft. Make sure all the oil holes in the rocker shaft and in the rocker levers are not clogged or plugged before beginning assembly procedure. When assembling, make sure bolt (8) and oil supply connection (9) are correctly positioned on the rocker shaft (7). Lubricate the components with clean engine oil before beginning assembly procedure. For assembly of the rocker shaft assembly, reverse the disassembly steps. Refer to the 3054 & 3056 Diesel Engines Systems Operation & Testing & Adjusting Manual, SENR5542 for procedure to set the valve clearance on the engine.End By:a. install rocker shaft assembly


Parts decal JOHNSON:

0283783
 
0283783 DECAL SET, 90/110 models
J100STLCEM, J100STLEIE, J100STLESB, J110MLCEM, J115JLEIE, J115MLESB, J85TTLEIE, J88MSLCER, J88MSLCER, J88MSLEIM, J88MSLEIM, J88MSLESA, J88MSLESA
0283784
 
0283784 DECAL SET, 100STL
J100STLCEM, J100STLEIE, J100STLESB, J110MLCEM, J115JLEIE, J115MLESB, J88MSLCER, J88MSLCER, J88MSLEIM, J88MSLEIM, J88MSLESA, J88MSLESA
0283782
 
0283782 DECAL SET, 88 models
J100STLCEM, J100STLEIE, J100STLEND, J100STLERC, J100STLESB, J100STLETS, J110MLCEM, J112TSLERS, J112TSLERS, J115JLEIE, J115JLEND, J115JLERC, J115JLETS, J115MLESB, J88MSLCER, J88MSLCER, J88MSLEIM, J88MSLEIM, J88MSLENB, J88MSLENB, J88MSLERD, J88MSLERD,
0284274
 
0284274 DECAL SET, 90/115 Jet
J100STLEIE, J115JLEIE, J88MSLEIM, J88MSLEIM
0284273
 
0284273 DECAL SET, 90/115
J100STLEIE, J100STLEND, J100STLETS, J115JLEIE, J115JLEND, J115JLETS, J88MSLEIM, J88MSLEIM, J88MSLENB, J88MSLENB, J88MSLETE, J88MSLETE
0284344
 
0284344 DECAL SET
J100STLEND, J100STLERC, J100STLETS, J115JKLERS, J115JLEND, J115JLERC, J115JLETS, J85TTLEND, J85TTLERC, J85TTLETS, J88MSLENB, J88MSLENB, J88MSLERD, J88MSLERD, J88MSLETE, J88MSLETE
0284347
 
0284347 DECAL SET, 90/115 Jet
J100STLEND, J115JLEND, J88MSLENB, J88MSLENB
0284346
 
0284346 DECAL SET, 90/115, 25"
J100STLEND, J100STLETS, J115JLEND, J115JLETS, J88MSLENB, J88MSLENB, J88MSLETE, J88MSLETE
Back to top