5031131 JOHNSON DECAL, Engine cover, front


5031131 DECAL, Engine cover, front JOHNSON J5REEC, J5RLSSA DECAL

Buy DECAL, Engine cover, front 5031131 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Compatible models:

J5REEC   J5RLSSA   JOHNSON

BRP JOHNSON entire parts catalog list:

J5REEC, J5RLEEC 1999
J5RLSSA, J5RSSA 2000

Information:


Table 1
Diagnostic Trouble Codes
CDL Code J1939 Code Code Description
(code descriptions may vary) Comments
E539 (1) 105-15 High Intake Manifold Air Temperature The code indicates that the temperature of the intake air into the engine has risen above a predetermined threshold. The value is obtained from a virtual sensor. For information on virtual sensors, refer to System Operations and Testing and Adjusting.
Engine power may be derated.
E539 (2) 105-16 High Intake Manifold Air Temperature The code indicates that the temperature of the intake air into the engine has risen above a predetermined threshold. The value is obtained from a virtual sensor. For information on virtual sensors, refer to System Operations and Testing and Adjusting.
Engine power may be derated.
E539 (3) 105-0 High Intake Manifold Air Temperature The code indicates that the temperature of the intake air into the engine has risen above a predetermined threshold. The value is obtained from a virtual sensor. For information on virtual sensors, refer to System Operations and Testing and Adjusting.
Engine power may be derated.
Follow the troubleshooting procedure in order to identify the root cause of the problem.
Illustration 1 g02894017
Inspection point
Table 2
Troubleshooting Test Steps Values Results
1. Check the Aftercooler for Leaks or Restrictions
A. Inspect the exterior surface of the ATAAC for excessive buildup of dirt or debris. Also verify that the fins of the ATAAC are not damaged.
Restrictions
Result: The ATAAC has an excessive buildup of dirt or debris.
Clean the ATAAC. Refer to the machine Test and Adjust manual. Verify that the problem has been resolved.
If the problem still exists, proceed to Test Step 2.
Result: The surface of the ATAAC is damaged.
Replace the ATAAC.
If the problem still exists, proceed to Test Step 2.
Result: The surface of the ATAAC is not damaged and the ATAAC does not have an excessive buildup of dirt or debris.
Proceed to Test Step 2.
2. Check the Operation of the Cooling Fan
A. Verify that the cooling fan that is being used to transfer heat from the ATAAC is working properly.
B. If the fan is belt driven, verify that the belt tension is adequate. Also, verify that the clutch is operating properly.
C. If the fan is hydraulically driven, verify that there is no leakage around the motor and that the pressure for the fan is adequate.
Cooling fan
Result: The fan drive system is not working properly.
Make the necessary adjustments to the clutch or the belt tension if the fan is mechanically driven . Refer to the machine Test and Adjust for the proper procedure. Repair leaks or make the necessary adjustments to the motor or the hydraulic pump if the fan is hydraulically driven . Refer to Testing and Adjusting for the proper procedure.
If the problem still exists, proceed to Test Step 3.
Result: The fan drive system is working properly.
Proceed to Test Step 3.
3. Check the Operation of the Charge Air Cooler Outlet Temperature Sensor
A. Remove the charge air cooler outlet temperature sensor. Allow the charge air cooler outlet temperature sensor to rest in ambient air for 2 minutes.
B. Connect to the engine ECM by using Cat ET.
C. Monitor the value of the charge air cooler outlet temperature sensor on Cat ET.
Sensor
Result: The value of the charge air cooler outlet temperature sensor is within −9° C ( 15° F) of the ambient temperature.
Reinstall the sensor. Torque the sensor to the proper specifications. Return the unit to service.
Result: The value of the charge air cooler outlet temperature sensor is not within −9° C ( 15° F) of the ambient temperature.
Replace the charge air cooler outlet temperature sensor. Return the unit to service.
Complete the procedure in the order in which the steps are listed.If the procedure corrected the issue, return the engine to service.If the procedure did not correct the issue, Contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts decal JOHNSON:

5030204
 
5030204 DECAL, Shift
J10R4SNF, J15R4SNF, J5RECS, J5REEC, J5RLSIM, J5RLSSA
5030226
 
5030226 DECAL, Stop
BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC, J10BL4SUM, J10EL4SDA, J10EL4SOR, J10EL4SRC, J10R4SDM, J10R4SNF, J10R4SR, J10R4STC, J10R4SUB, J10RL4SDM, J10TBL4SDE, J10TBL4SUD, J10TE4SDM, J15EL4SDC, J15EL4SOS, J15EL4SUR, J15R4SDM,
5030293
DECAL, Fuel valve assy.
5030293 DECAL, Fuel valve assy.
J5RECS, J5REEC, J5RLSIM, J5RLSSA
5030316
DECAL, Handle grip
5030316 DECAL, Handle grip
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4STC, J50PL4STC, J5RECS, J5REEC, J5RLSIM, J5RLSSA
5031132
5030304
 
5030304 DECAL, Safety warning
J5REEC, J5RLSIM, J5RLSSA
Back to top