5032485 JOHNSON *DECAL, Port


5032485 *DECAL, Port JOHNSON J5RLSIM DECAL
5032485 *DECAL, Port JOHNSON
Rating:
93

Buy *DECAL, Port 5032485 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$224.25
 

23-03-2021
13.0[5.85] Pounds
-: -
Spyder 5032485 Chevy Avalanche 07-13 LED Tail Lights - Smoke
Update your car or truck's look || Top quality taillights with OEM fitment for a simple bolt-on installation || Please verify fitment before purchasing || These lights are made by an OE approved and ISO certified manufacturer with the quality meet or exceed all OE standards || Some of the package includes light bulbs, for package which does not come with any light bulbs, you can apply the stock light bulbs for installation
$252.51
 

18-09-2017
14.00[6.30] pounds
Spyder Aut: Spyder Auto
Spyder Auto 5032485 LED Tail Lights Chrome/Smoked
Spyder Auto a trusted industry leader||Backed by Manufacturer's Warranty||Enhance your vehicle||LED||Chrome/Smoked
Number on catalog scheme: 6
 

Compatible models:

J5RLSIM   JOHNSON

BRP JOHNSON entire parts catalog list:

J5RLSIM, J5RSIM, J5RVLSIM, J5RVSIM 2001

Information:


Illustration 1 g00664421
Illustration 2 g00664423
Refer to the engine wiring diagram for the configuration of the wiring.The TCM monitors the characteristic resistance of the sensor in order to diagnose open circuits and short circuits.Test Step 1. Check for Connector Damage.
Remove the power from the timing control system.
Check the connectors and wiring for the following problems: damage, corrosion, abrasion and incorrect attachment. Refer to Troubleshooting, "Inspecting Electrical Connectors".Expected Result:The connectors and wiring are free of the following problems: damage, corrosion, abrasion and incorrect attachment.Results:
OK - The connectors and wiring are in good condition. Proceed to test step 2.
Not OK - The connectors and/or wiring require service.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Reconnect all of the connectors. Stop.Test Step 2. Check the Resistance of the Sensor.
Disconnect the speed sensor from the engine harness.
Use the 4000 ohm scale to measure the resistance between pin A and pin B at the sensor connector.Note: Be sure that you measure the resistance at the sensor connector. Do not measure the resistance at the harness connector.Expected Result:The resistance is between 100 and 600 ohms.Results:
OK - The sensor is OK. Proceed to test step 3.
Not OK - The sensor is faulty.Repair: Replace the sensor. Reconnect all of the connectors. Stop.Test Step 3. Check the Engine Harness.
Connect the speed sensor to the engine harness.
Disconnect the TCM from the engine harness.
Measure the resistance at the connector for the TCM. Use the 4000 ohm scale to measure the resistance between pin T and pin N.Expected Result:The resistance is between 100 and 600 Ohms. The value is equal to the reading from test step 2.Results:
OK - The harness does not have an open circuit. Proceed to test step 4.
Not OK - There is an open circuit in the harness.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Stop.Test Step 4. Check the Clearance Between the Sensor and the Flywheel.
Disconnect the speed sensor from the engine harness.
Mark the position of the sensor on the flywheel housing.
Loosen the locknut.
Turn the sensor clockwise until the sensor contacts a tooth of the flywheel.Record the number of turns that are required to make contact. The correct number of turns for the proper clearance is approximately one-half to three-fourths of a turn (180 to 270 degrees).
Remove the sensor from the flywheel housing.
Inspect the sensor for damage and metal filings on the magnetic tip.
Install the speed sensor into the flywheel housing.
Turn the sensor clockwise until the sensor contacts a tooth of the flywheel ring gear.
Turn the sensor counterclockwise for approximately one-half to three-fourths of a turn (180 to 270 degrees).Note: Do not allow the sensor to move when you tighten the locknut.
Tighten the locknut to a torque of 45 7 N m (35 5 lb ft).Expected Result:The clearance was correct. The sensor is clean and undamaged.Results:
OK - The sensor is OK.Repair: Reset the system and troubleshoot any active diagnostics. If the fault returns, replace the TCM. Stop.
Not OK - The clearance was incorrect. The sensor is not clean and/or the sensor is damaged.Repair: If the sensor is damaged, replace the sensor. Clean the sensor, if necessary. Install the sensor. Stop.


Parts decal JOHNSON:

Back to top