0332678 JOHNSON DIAPHRAGM

Illustration 1 g01213005
Schematic of the ether injection system
Illustration 2 g01167488
Engine view (typical example)
(1) J1/P1 ECM connectors
Illustration 3 g01146383
Engine view (typical example)
(2) P61 customer connector
Illustration 4 g01170983
Ether starting aid group (typical example)
(3) Ether injection solenoid
Illustration 5 g01212950
P1 terminals for the ether injection system
(P1-10) Ether injection solenoid
(P1-22) Override switch
Illustration 6 g01212957
P61 terminals for the ether injection system
(22) Ether injection solenoid
(38) Override switch
Illustration 7 g01155187
Terminal locations at the harness connector for the ether solenoid
(1) Ether injection solenoid
(2) Chassis ground
Table 1
Troubleshooting Test Steps Values Results
1. Inspect the Electrical Connectors and the Wiring
A. Remove electrical power from the ECM.
B. Thoroughly inspect connectors (1) and (2). Also, thoroughly inspect the connectors for solenoid (3). Refer to Troubleshooting, "Electrical Connectors - Inspect".
C. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the ether injection system.
D. Check the allen head screw on each ECM connector for the proper torque. Also check the allen head screw on the customer connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
E. Check the harness and the wiring for abrasion and for pinch points from the ether injection solenoid to the ECM.
Electrical Connectors and Wiring
Results: The connectors and wiring appear to be OK. Proceed to Test Step 2.
Results: The connectors and/or wiring are not OK.
Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Verify that the problem is resolved.
STOP
2. Check the Ether Canister for Starting Fluid
A. Remove electrical power from the ECM.
B. Remove the ether canister from the ether valve. Determine if the canister contains fluid.
Starting Fluid
Results: The ether canister is not empty. Do not install the ether canister. Proceed to Test Step 3.
Results: The ether canister is empty.
Repair: Replace the empty ether canister with a full ether canister. Verify that the original problem is resolved.
STOP
3. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Restore electrical power to the engine ECM.
C. Proceed to the "Diagnostic Overrides" screen on Cat ET.
D. Activate the ether injection system. The system will activate for10 seconds.
E. Monitor the active diagnostic code screen on Cat ET. Check and record any active diagnostic codes.
F. Look for a 05 diagnostic code or a 06 diagnostic code.
G. Remove electrical power from the engine ECM.
Codes
Results: There are no active codes.
Repair: The problem seems to be resolved. The problem may have been caused by a poor electrical connection. Carefully reinspect the connectors and the wiring. Refer to Troubleshooting, "Electrical Connectors - Inspect".
STOP
Results: A 05 code is active at this time. The ECM is detecting a low current condition in the circuit. Proceed to Test Step 5.
Results: A 06 code is active at this time. The ECM is detecting excessive current in the circuit. Proceed to Test Step 4.
4. Create an Open at the Harness Connector for the Ether Injection Solenoid
A. Disconnect the harness connector for the ether solenoid.
B. Restore electrical power to the engine ECM.
C. Proceed to the "Diagnostic Overrides" screen on Cat ET.
D. Activate the ether injection system. The system will activate for 10 seconds.
E. Monitor the active diagnostic code screen on Cat ET. Look for an active 05 code.
Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
F. Remove electrical power from the engine ECM.
Open
Results: A 06 code was active before the connector was disconnected. A 05 code became active after the connector was disconnected.
Repair: The circuit for the ether solenoid is OK. Temporarily connect a new solenoid to the harness, but do not install the new solenoid. After connecting the new solenoid to the harness, verify that there are no active codes for the ether injection system. If there are no active codes for the ether injection system, permanently install the new solenoid. Clear any logged diagnostic codes.
STOP
Results: A 06 code was active before the connector was disconnected. The 06 code remained active after the connector was disconnected. There is a problem in the circuit for the ether injection solenoid. There may be a problem with the ECM. Leave the connector for the solenoid disconnected. Proceed to Test Step 6.
5. Create a Short at the Connector for the Ether Injection Solenoid
A. Disconnect the harness connector for the ether solenoid.
B. Fabricate a jumper wire that is long enough to create a short circuit between terminal 1 and terminal 2 at the harness connector for the ether solenoid. Crimp connector pins to each end of the jumper wire.
C. Install the jumper wire between terminals 1 and 2 of the harness connector.
D. Restore e