0321456 JOHNSON DRIVESHAFT,Long 5 INCH LONGER PARTS

Table 1
Error Number    Terminal Messages    Type    Meaning    Recommended Action    
200-206, 300, 318-321, 328, 329, 331, 346, 347, 355, 356, 358, 367, 404, 411, 416, 417, 421-425, 447-449, 457, 459, 700, 1105, 1111, 1113, 1115, 1207-1211, 2002-2009, 2016, 2018, 2021, 2028 and 2029     A fault has occurred. Error = X     Minor Fault or Terminal Fault     A minor fault was detected that could impact terminal operation or a terminal fault was detected.     Press any key to recover from a minor fault. For terminal faults, contact technical support with the error code.    
208     Write to logic controller failed     Comm Status     Controller does not accept data from the terminal. Controller is not connected.     Check connections (on Remote I/O units). Verify that controller is in run mode and not busy. Verify that controller data files are not in use by other applications.    
303     Aborted.     Reminder / File Transfer Status     The terminal received an abort command during a file transfer.     Try again.    
304     File read access error     Reminder     Error reading the source file from a source device.     Try again. If problem continues, contact technical support.    
305     File write access error     Reminder     Error writing source file.     Try again. If problem continues, contact technical support.    
307     File not supported     Reminder / File Transfer Status     File is incompatible with the terminal's firmware.     Contact technical support to verify compatibility. File must be a .PVA file.    
308     Timeout     Reminder / File Transfer Status     The terminal was waiting for the partner device in a file transfer, but the terminal timed out before the data or expected reply was received.     Check cable connections or data corruption with noise on cable. Verify that the computer was not reset. Try again.    
309-311     Data corrupted. Verify file and retry.     Reminder / File Transfer Status     The data checksum failed in a file transfer.     Check electrical and cable connections. Try the file transfer again.    
312     Unknown device     Reminder / File Transfer Status     Verify the file type entered. Try again.     Destination or source device is invalid for a read or write application transfer.    
313     File too large     Reminder / File Transfer Status     Reduce application size. See Appendix A for terminal requirements. If copying to a card, check card space.     File too large to be transferred to the terminal. In a memory card transfer, the card does not have enough space.    
314     No Card Inserted     Reminder     Install a memory card and try again.     You tried to transfer data to/from a memory card but there is no card in the card slot.    
315     Unformatted card     Reminder     Memory card is unformatted, contains an unrecognizable format or is corrupt.     Reformat the card or replace it with a new card if corrupt. Try again.    
316     Write Protected Card     Reminder / File Transfer Status     A write command to the card failed because the card switch is in the protected mode.     Select write mode by changing the switch on the top edge of the card. Try again.    
317     File exists. Cannot overwrite     Reminder / File Transfer Status     See message 342. This message only occurs when the file cannot be renamed.     Change the file name or save to a new memory card.    
323     No application on PV terminal     Reminder / File Transfer Status     You tried to load an application on a memory card but there is no application in the terminal.     View the Terminal Info screen to see if an application is loaded in the terminal.    
324     Check card status     Reminder / File Transfer Status     Problem formatting the memory card.     Try a new memory card.    
325     Unformatted card     Reminder     Memory card is unformatted, contains an unrecognizable format or is corrupt.     Reformat the card or replace it with a new card. Try again.    
326     No Card Inserted     Reminder     You tried to transfer data to/from a memory card but there is no card in the card slot.     Install a memory card and try again.    
327     No files     Reminder     You tried to transfer a file from the memory card but there are no files on the card.     Use memory card containing application (.PVA) files.    
330     Write Protected Card     Reminder / File Transfer Status     A write command to the card failed because the card switch is in the protected mode.     Select write mode by changing the switch on the top edge of the card. Try again.    
332     No application on PV terminal     before removal.     You tried to load an application on a memory card but there is no application in the terminal.     View the Terminal Info screen to see if an application is loaded in the terminal.    
333     File in use - Request denied     Reminder     Attempt to format memory card containing a file used by the application. This usually occurs when an application requires a font file on the memory card.     Format the memory card on a computer or a PanelView terminal that does not have an application loaded.    
334     Unexpected card removal. Please disconnect card before removal.     Reminder / File Transfer Status     You removed the memory card during normal operation and did not press the Disconnect button on the Memory Card configuration screen.     Press the Disconnect Card button to close the files on the card. When prompted, remove the card from the slot and then re-insert the card. Enter Configuration Mode and press the Run Mode button.    
340     Format erases entire card: 0 - Abort, 1 -