0342369 DRIVESHAFT SHIELD & O-RING JOHNSON
BJ20SRECB, BJ20SREUM, BJ25BAECM, BJ25BAEUA, BJ30BAECS, BJ30BAEEC, BJ30BAEUD, J25JREDC, J25JREEM, J25JREOS, J25JRSIE, J25JRSSB, J30RLSIA, J30RLSSR
DRIVESHAFT
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- JET DRIVE UNIT » 0342369
BJ25BAECM, BJ25BALECM, J25JRECA, J25RECB, J25RLECB, SJ25RDECA 1998
BJ25BAEUA, BJ25BALEUA, HJ25RAEUM, J25JREUR, J25REUM, J25RLEUM, SJ25RDEUR 1997
BJ30BAECS, BJ30BALECS 1998
BJ30BAEEC, BJ30BAEEN, J30REEC, J30REEN, J30RLEEC, J30RLEEN 1999
BJ30BAEUD, BJ30BALEUD, J30REUD, J30RLEUD 1997
J25JREDC 1996
J25JREEM, J25JREEN, J25REEB, J25REEN, J25RLEEB, J25RLEEN, SJ25RDEEM, SJ25RDEEMN, SJ25RTEEM 1999
J25JREOS 1995
J25JRSIE, J25RLSID, J25RSID, J25RVLSID, J25RVSID, SJ25RTSIE 2001
J25JRSSB, J25RLSSE, J25RSSE, SJ25RTSSB 2000
J30RLSIA, J30RSIA, J30RVLSIA, J30RVSIA 2001
J30RLSSR, J30RSSR 2000
Information:
start by:a) remove oil pump1. Check the main bearing caps for identification for their location and direction in the block. The caps must be installed in the same location and direction from which they were removed. 2. Remove No. 2 through No. 6 bearing caps (1). Remove thrust bearings from No. 4 main bearing cap. 3. Remove the upper halves of main bearings by the installation of tool (A) in oil hole (2) in the crankshaft. Turn the crankshaft in the direction which will push the end of the bearing with a tab out first.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and cylinder block. This can cause damage to either or both.
4. Remove the lower halves of the bearings from the caps.5. Install new bearings in the caps. Put clean engine oil on the bearings.6. Put clean engine oil on the upper halves of the bearings. Install the upper halves of the bearings in the cylinder block with tool (A). Be sure tabs (3) on the back of the bearings fit in the grooves of the caps and cylinder block.7. Check the bearing clearance with Plastigage. Put plastigage on the bearings. Make sure the crankshaft is held up against the upper main bearings before the bearing clearance is checked. The Plastigage will not hold the weight of the crankshaft and give a correct indication. Do not turn crankshaft when Plastigage is in position to check clearance. Be sure the main bearing caps are installed so the numbers on the side of the cylinder block are the same as the numbers on the bearing caps, and the arrows (4) on the bearing caps are toward the front of the cylinder block.8. Install the bearing caps for No. 2 through No. 6. Put clean engine oil on the bolts. Install the bolts and tighten bolts, at end with tab first, to a torque of 190 10 lb.ft. (260 14 N m). Turn the bolts an extra 120° 5° first at the end opposite of the tab. Remove the bearing caps for No. 2 through No. 6. Remove Plastigage from the caps. Check the thickness of Plastigage to find the bearing clearance. The bearing clearance must be .0036 to .0073 in. (0.091 to 0.185 mm) with new bearings. The maximum permissible clearance with used bearings is .010 in. (0.254 mm). 9. Put clean engine oil on the threads of the bolts. Install bearing caps (5) for No. 2 through No. 6 main bearings. Install the bolts and tighten the bolts, at the end with the tab first, to a torque of 190 10 lb.ft. (260 14 N m). Put a mark on the bolts and caps. Turn the bolts at opposite end of tab first an extra 120° 5° from the mark.10. Remove the No. 1 and No. 7 main bearing caps. Do Steps 3 through 9 for the No. 1 and No. 7 caps.11. Install the thrust bearings for No. 4 main bearing. Install the thrust bearings with the side that has the identification "BLOCK SIDE" toward the cylinder block. 12. Check the end play of the crankshaft with tool group (C). Be sure the dial indicator is against a machined surface. The end play is controlled by the thrust bearings of No. 4 (center) main. The end play with new bearings must be .006 to .020 in. (0.152 to 0.508 mm). The maximum permissible end play with used bearings is .035 in. (0.89 mm).end by:a) install oil pump
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and cylinder block. This can cause damage to either or both.
4. Remove the lower halves of the bearings from the caps.5. Install new bearings in the caps. Put clean engine oil on the bearings.6. Put clean engine oil on the upper halves of the bearings. Install the upper halves of the bearings in the cylinder block with tool (A). Be sure tabs (3) on the back of the bearings fit in the grooves of the caps and cylinder block.7. Check the bearing clearance with Plastigage. Put plastigage on the bearings. Make sure the crankshaft is held up against the upper main bearings before the bearing clearance is checked. The Plastigage will not hold the weight of the crankshaft and give a correct indication. Do not turn crankshaft when Plastigage is in position to check clearance. Be sure the main bearing caps are installed so the numbers on the side of the cylinder block are the same as the numbers on the bearing caps, and the arrows (4) on the bearing caps are toward the front of the cylinder block.8. Install the bearing caps for No. 2 through No. 6. Put clean engine oil on the bolts. Install the bolts and tighten bolts, at end with tab first, to a torque of 190 10 lb.ft. (260 14 N m). Turn the bolts an extra 120° 5° first at the end opposite of the tab. Remove the bearing caps for No. 2 through No. 6. Remove Plastigage from the caps. Check the thickness of Plastigage to find the bearing clearance. The bearing clearance must be .0036 to .0073 in. (0.091 to 0.185 mm) with new bearings. The maximum permissible clearance with used bearings is .010 in. (0.254 mm). 9. Put clean engine oil on the threads of the bolts. Install bearing caps (5) for No. 2 through No. 6 main bearings. Install the bolts and tighten the bolts, at the end with the tab first, to a torque of 190 10 lb.ft. (260 14 N m). Put a mark on the bolts and caps. Turn the bolts at opposite end of tab first an extra 120° 5° from the mark.10. Remove the No. 1 and No. 7 main bearing caps. Do Steps 3 through 9 for the No. 1 and No. 7 caps.11. Install the thrust bearings for No. 4 main bearing. Install the thrust bearings with the side that has the identification "BLOCK SIDE" toward the cylinder block. 12. Check the end play of the crankshaft with tool group (C). Be sure the dial indicator is against a machined surface. The end play is controlled by the thrust bearings of No. 4 (center) main. The end play with new bearings must be .006 to .020 in. (0.152 to 0.508 mm). The maximum permissible end play with used bearings is .035 in. (0.89 mm).end by:a) install oil pump
Parts driveshaft JOHNSON:
0437810
0437810 DRIVESHAFT & SLEEVE ASSY.
BJ20SRECB, BJ20SREUM, BJ25BAECM, BJ25BAEUA, BJ30BAECS, BJ30BAEEC, BJ30BAEUD, J25JREDC, J25JREEM, J25JREOS, J25JRSIE, J25JRSSB, J30RLSIA, J30RLSSR
0341635
0341635 DRIVESHAFT, Std.
BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25EECE, BJ25EEDM, BJ25EEED, BJ25EEUB, BJ25ELSIC, BJ25ELSSS, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, BJ30EECS, BJ30EEDE, BJ30EEEC, BJ30EEUD, BJ30E
0341638
0341638 DRIVESHAFT, Long
BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25EECE, BJ25EEDM, BJ25EEED, BJ25EEUB, BJ25ELSIC, BJ25ELSSS, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, BJ30EECS, BJ30EEDE, BJ30EEEC, BJ30EEUD, BJ30E
0341636
0341636 DRIVESHAFT, Std.
HJ25FPO, HJ25FPV, J25JRSSB, J25WREEN, J25WRLSIR, J25WRLSSC, J30RLSSR, SJ25RPLP