0437377 JOHNSON DRIVESHAFT, RSY model only


0437377 DRIVESHAFT, RSY model only JOHNSON J65RSLC, J65RSLM, J65RSLZ2, J65WMLEOC, J65WRLEEO, J65WRLSIR, J65WRLSSC, SJ65RSLD, SJ65WMLD, SJ65WMLM, SJ65WMLZ2 DRIVESHAFT
0437377 DRIVESHAFT, RSY model only JOHNSON
Rating:
83

Buy DRIVESHAFT, RSY model only 0437377 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 33
 

BRP JOHNSON entire parts catalog list:

J65RSLC 1995
J65RSLM, SJ65RSLM, SJ65RSYM 1996
J65RSLZ2, SJ65RSLZ2, SJ65RSYZ2 1997
J65WMLEOC 1995
J65WRLEEO, J65WRLEES, J65WRYEEO, J65WRYEES 1999
J65WRLSIR, J65WRYSIR 2001
J65WRLSSC, J65WRYSSC 2000
SJ65RSLD, SJ65RSYD 1998
SJ65WMLD, SJ65WMYD 1998
SJ65WMLM, SJ65WMYM 1996
SJ65WMLZ2, SJ65WMYZ2 1997

Information:

Parameter Descriptions
"Rating Number"
"Rating Number" is a reference number that corresponds to the rating map that is resident in the personality module (flash file). Flash files may contain more that one rating."Equipment ID"
The "Equipment ID" parameter allows the customer to enter a description into the ECM in order to identify the machine. A maximum of 17 characters can be entered in the field."Engine Serial Number"
The "Engine Serial Number" should be programmed to match the engine serial number that is stamped on the engine information plate. The engine serial number is not preprogrammed on a replacement ECM."FLS" (Full Load Setting)
"FLS" is a number that represents the adjustment to the fuel system that was made at the factory in order to fine tune the fuel system. The correct value for this parameter is stamped on the engine information ratings plate. This value should only be changed if the engine is rerated or a new ECM is installed. Factory passwords are required."FTS" (Full Torque Setting)
"FTS" is similar to "FLS". This value should only be changed if the engine is rerated or a new ECM is installed. Factory passwords are required."Engine Oil Weight"
Setting this parameter to the correct oil grade that is in the engine will aid in cold weather starting. Do not program this parameter to "Automatic Detection"."Idle Quality Adjustment"
This parameter is used to fine tune the idle quality of the engine."Number of Available Engine Power Levels"
The "Number of Available Engine Power Levels" parameter is programmed at the factory to enable the use of variable power levels. Factory passwords are required."Battery Elevated Idle"
The "Battery Elevated Idle" parameter allows the operation of this feature to be enabled or disabled. Refer to Troubleshooting, "Elevated Idle" for more information.Parameter Table
Table 1
System Configuration Parameters    
Parameter    Available Range or Options    Default    Required Password    
"Rating Number"     Application Dependent     none    
"Equipment ID"     17 characters     blank     none    
"Engine Serial Number"     8 characters     blank     none    
"FLS"     -128 to +127     0     Factory    
"FTS"     -128 to +127     0     Factory    
"Engine Oil Weight"     "0W20 oil grade"
"10W30 oil grade"
"15W40 oil grade"     "15W40 oil grade"     none    
"Idle Quality Adjustment"     Decrease 1, 2, 3, or 4
Increase 1, 2, 3, or 4     Nominal     none    
"Number of Available Engine Power Levels"     1 to 2     Application Dependent     Factory    
"Battery Elevated Idle"     "On" or "Off"     "On"     none    Parameter Worksheet
Record the following information before you change any programmable parameter.
Table 2
Information from ECM    
"Rating Number"    
   
"Equipment ID"    
   
"Engine Serial Number"    
   
"ECM Serial Number"    
   
"Personality Module Part Number"    
   
"Personality Module Release Date"    
   
"Personality Module Description"    
   
"FLS"    
   
"FTS"    
   
"Engine Oil Weight"    
   
"Idle Quality Adjustment"    
   
"Number of Available Engine Power Levels"    
   
"Battery Elevated Idle"    
   
"Total Tattletale"    
   
Information From Engine Information Plate    
Engine Serial Number    
   
Fuel Air Ratio(for new ECM)    
   
Full Load Setting (for new ECM)    
   
Full Torque Setting (for new ECM)    
   Note: Compare the FLS and the FTS from the ECM with the values that are listed on the Engine Information Plate. The FLS and the FTS should only be changed because of a mechanical change in the engine. The use of the wrong parameters could cause damage to the engine. The use of the wrong parameters may also void the Caterpillar warranty.


Parts driveshaft JOHNSON:

0437376
 
0437376 DRIVESHAFT ASSY., Long, 20 in. only
BJ50DTLEDC, BJ50DTLEUR, BJ60ELEDR, BJ60ELEUA, BJ60TLECM, BJ70ELECB, BJ70ELEDA, BJ70ELEUM, BJ70PLEEE, BJ70PLSIS, BJ70PLSSD, J40JPLEEC, J40JPLSIA, J40JPLSSR, J50DTLECA, J50DTLEOS, J50TTLECA, J50TTLEDC, J50TTLEOS, J50TTLEUR, J60ELEOC, J60PLEEB, J60PLSID
Back to top