0283567 JOHNSON ENGINE COVER ASSY., 175STL


0283567 ENGINE COVER ASSY., 175STL JOHNSON J150CXCEM, J150CXEIE, J150CXESB, J175STLCEB, J175STLEID, J175STLESE ENGINE
0283567 ENGINE COVER ASSY., 175STL JOHNSON
Rating:
23

Buy ENGINE COVER ASSY., 175STL 0283567 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

BRP JOHNSON entire parts catalog list:

J150CXCEM, J150TLAEM, J150TLCEM, J150TXCEM, TJ150TXCEM 1989
J150CXEIE, J150JLEIE, J150TLAIE, J150TLEIE, J150TXEIE, VJ150TLEIE, VJ150TXEIE 1991
J150CXESB, J150TLASB, J150TLESB, J150TXESB, VJ150TLESB, VJ150TXESB 1990
J175STLCEB, J175TXCEB 1989
J175STLEID, J175TXEID, VJ175SLEID, VJ175TXEID 1991
J175STLESE, J175TXESE, VJ175SLESE, VJ175TXESE 1990

Information:


Wear goggles, gloves, protective clothing, and a National Institute for Occupational Safety and Health (NIOSH) approved P95 or N95 half-face respirator when handling a used Diesel Particulate Filter or Catalytic Converter Muffler. Failure to do so could result in personal injury.
The muffler, catalytic converter/muffler, and diesel particulate filter will become extremely hot during engine operation. A hot muffler, catalytic converter/muffler and diesel particulate filter can cause serious burns. Allow adequate cooling time before working on or near the muffler, catalytic converter/muffler and diesel particulate filter.
Do not strike any part of the assembly of the Diesel Oxidation Catalyst (DOC). Do not allow any object to contact the internal element of the DOC. If the internal element of the DOC becomes damaged, the assembly must be replaced.
Illustration 1 g02360116
If necessary, remove the Original Equipment Manufacturers (OEM) exhaust system from outlet cannister (4) of the clean emission module.
Make temporary alignment marks on Torca clamp (3) in Position (A) and Position (B). Loosen the nuts for Torca clamp (3) and slide the Torca clamp along the Diesel Particulate Filter (DPF).
Sufficiently loosen the nuts on clamp (2) in order to allow the Diesel Oxidation Catalyst (DOC) (1) to be removed.
Loosen the bolt on ball clamp (5) in order to allow the removal of DOC (1) .
Illustration 2 g02360117
Illustration 3 g02360118
Disconnect harness assembly (7) from soot antenna (8) .
Remove temperature sensor (6) .
Remove soot antenna (8) .
Disconnect nut (11) for tube assembly (10) .
Slide hose clamp (9) along the hose assembly. Remove tube assembly (10) .
Illustration 4 g02360119
Make temporary alignment mark on DOC (1) and Diesel Particulate Filter (DPF) in Position (C) .
Attach a suitable lifting device to DOC (1). The weight of the DOC is approximately 20 kg (44 lb).
Rotate the DOC in a counter clockwise direction in order to disengage pins and slots (12) from the DPF.
Use the suitable lifting device to remove DOC (1) from the clean emission module mounting bracket.
Remove Torca clamp (3) .
Remove ball clamp (5) .Installation Procedure
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Illustration 5 g02360119
Position a new Torca clamp (3) onto the DPF. Ensure the correct orientation of the Torca clamp (3) .
Position a new ball clamp (5) onto DOC (1). Ensure the correct orientation of ball clamp (5) .
Attach a suitable lifting device to DOC (1). The weight of the DOC is approximately 20 kg (44 lb).
Use the suitable lifting device to position DOC (1) onto the clean emission module mounting bracket and align pins and slots (12) .
Rotate DOC (1) in a clockwise direction in order to engage pins and slots (12) as in Position (C). Ensure that the pins and slots are fully engaged.
Illustration 6 g02328556
Illustration 7 g02360119
Position ball clamp (5) and hand tighten the bolt. Ensure that the ball clamp is correctly orientated.
Slide Torca clamp (3) along the DPF ensure that Torca clamp is correctly orientated.
Position the Torca clamp between Position (A) and Positions (B). Hand tighten the Torca clamp. Ensure that the Torca clamp is correctly aligned.
Illustration 8 g02360116
Tighten the nuts on clamp (2) for DOC (1) and the DPF hand tight.
Tighten nuts for Torca clamp (3) to a torque of 42 N m (31 lb ft).
Tighten the nuts for clamp (2) to a torque of 18 N m


Parts engine JOHNSON:

0283910
 
0283910 ENGINE COVER ASSY., TE150TX
J150CXCEM, J175STLCEB
0283639
 
0283639 ENGINE COVER ASSY., 150CX
J150CXCEM, J150CXEIE, J150CXESB, J175STLCEB, J175STLEID, J175STLESE
0283638
 
0283638 ENGINE COVER ASSY., 150 TL
J150CXCEM, J150CXEIE, J150CXESB, J175STLCEB, J175STLEID, J175STLESE
0283681
 
0283681 ENGINE COVER ASSY., 175
J150CXCEM, J150CXEIE, J150CXESB, J175STLCEB, J175STLEID, J175STLESE
0283682
 
0283682 ENGINE COVER ASSY., 150 TX
J150CXCEM, J150CXEIE, J150CXESB, J175STLCEB, J175STLEID, J175STLESE
0584016
 
0584016 ENGINE CABLE ASSY.
J150CXESB, J175STLESE
0282199
0434088
 
0434088 ENGINE COVER ASSY., 150TLA
J150CXEIE, J175STLEID
Back to top