0284116 JOHNSON ENGINE COVER ASSY., 200STL, VE200SL


0284116 ENGINE COVER ASSY., 200STL, VE200SL JOHNSON J185ESXENR, J200CXENE, J225CXENR ENGINE
0284116 ENGINE COVER ASSY., 200STL, VE200SL JOHNSON
Rating:
88

Buy ENGINE COVER ASSY., 200STL, VE200SL 0284116 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 28411
 

Compatible models:

BRP JOHNSON entire parts catalog list:

J185ESXENR 1992
J200CXENE, J200STLENS, J200TXENE, VJ200SLENS, VJ200TXENE 1992
J225CXENR, J225PLENR, J225PXENR, J225TLENR, J225TXENR, VJ225PLENR, VJ225PXENR, VJ225TLENR, VJ225TXENR 1992

Information:


See the service manual for your engine for other adjusting procedures.
Rack Adjustment For Engines With NSFS
Rear Of Governor
1. Opening for variable power actuator.1. Remove the variable power actuator from the rear of the governor.2. Adjust the high power fuel setting using the standard fuel system setting procedure in the service manual.For the correct fuel setting specifications, see the Engine Information Plate or the FUEL SETTING AND RELATED INFORMATION FICHE.
6V7941 Compressor Assembly
Governor And Compressor
2. 6V7941 Compressor Assembly.3. Remove the 6V7941 Compressor Assembly (2) and replace the plug in the rear of the governor housing.
Variable Power Actuator
3. Rod. 4. Washered nut. 5. Jam nut. 6. Dust cover.4. Remove the dust cover (6) from the variable power actuator. Loosen the jam nut (5) on the rod (3). Tighten the washered nut (4) to put rod (3) in the fully retracted position.
Governor And Actuator
3. Rod. 4. Washered nut. 5. Jam nut. 7. Actuator.5. Install actuator (7) in governor housing opening (1).6. Move the governor control to the high idle position and hold or fasten the governor control in this position.7. Extend the actuator rod (3), by loosening the washered nut (4), to achieve a minimum dial indicator reading of 2.0 mm (.08 in.) less than the desired low power fuel setting.EXAMPLE: If the low power rack adjustment specification is 3.0 mm (.12 in.), the actuator rod (3) must be adjusted to obtain a dial indicator reading of 1.0 mm (.04 in.).8. Tighten the washered nut (4), to retract the actuator rod (3) and increase the dial indicator reading to the specified low power fuel setting.For the correct fuel setting specifications, see the Engine Information Plate or the FUEL SETTING AND RELATED INFORMATION FICHE.9. If the low power fuel setting is exceeded, repeat steps 7 and 8.10. Tighten the jam nut (5) on the actuator rod (3) and install the dust cover (6).3304 SMFS Air Only Actuator
See the service manual for your engine for other testing and adjusting procedures.
Rack Adjustment For Engines With Sleeve Metering Fuel System (SMFS)
1. Remove the variable power actuator (1) from the rear of the governor (2).2. Use the fuel setting procedure in the service manual and adjust the high power fuel setting screw.For the correct fuel setting specifications, see the Engine Information Plate or the FUEL SETTING AND RELATED INFORMATION FICHE.3. Install the variable power actuator (1).4. Remove the back cover (6) from the actuator (1) to expose the adjustment pin (5).5. Move the governor control shaft to the high idle position.6. Turn the adjustment pin (5) clockwise to adjust the variable power control rod (8) to the fully EXTENDED position.7. To adjust the low power setting, turn the adjustment pin (5) counterclockwise to retract rod (8). Retract the rod (8) until the rack setting is decreased to the specified setting.For the correct fuel setting specifications, see the Engine Information Plate or the FUEL SETTING AND RELATED INFORMATION FICHE.8. Replace cover (6) on the variable power actuator (6).
Governor And Variable Power Actuator
1. Variable power actuator. 2. Governor.
Governor And Variable Power Actuator
2. Governor. 3. Lever. 4. Spring. 5. Adjustment pin. 6. Cover. 7. Air port. 8. Rod.


Parts engine JOHNSON:

0432783
 
0432783 ENGINE COVER & SEAL ASSY., Stbd.
J185ESXENR, J185ESXESS, J185ESXW, J200CXCEA, J200CXEIB, J200CXENE, J200CXESM, J225CXCED, J225CXEIC, J225CXENR, J225CXESS
0434390
ENGINE COVER, Port
0434390 ENGINE COVER, Port
BJ130PLEED, BJ130PLSSS, BJ130TLECE, BJ130TLEDM, BJ130TLEUB, J120TLAIE, J120TLAND, J120TLARC, J120TLATF, J125ESXENR, J125ESXERK, J125ESXETA, J125WTPLE, J130CXAOR, J140CXARC, J140CXATF, J140CXEIA, J140CXENM, J185ESXENR, J200CXEIB, J200CXENE, J225CXEIC,
0284171
 
0284171 ENGINE COVER ASSY., 185
J185ESXENR, J200CXENE, J225CXENR
0284202
 
0284202 ENGINE COVER ASSY., 225TX
J185ESXENR, J200CXENE, J225CXENR
0284102
 
0284102 ENGINE COVER ASSY., 225TL
J185ESXENR, J200CXENE, J225CXENR
0284201
 
0284201 ENGINE COVER ASSY., 200CX
J185ESXENR, J200CXENE, J225CXENR
0284103
 
0284103 ENGINE COVER ASSY., 225PL
J185ESXENR, J200CXENE, J225CXENR
0584404
 
0584404 ENGINE CABLE ASSY.
J185ESXENR, J200CXENE, J225CXENR
Back to top