0284128 ENGINE COVER ASSY. JOHNSON
J20EEND, J20EERC, J20EETS, J25EENS, J25EERR, J25EETC, J30EENR, J30EERM, J30EETA
ENGINE
Price: query
Rating:
BRP JOHNSON entire parts catalog list:
- ENGINE COVER - EVINRUDE » 0284128
J20EETS, J20ELETS 1993
J25EENS, J25ELENS, TJ25ELENS, VJ25ELENS 1992
J25EERR, J25ELERR 1994
J25EETC, J25ELETC, TJ25ELETC, VJ25ELETC 1993
J30EENR, J30ELENR, VJ30EENR, VJ30ELENR 1992
J30EERM, J30ELERM 1994
J30EETA, J30ELETA, VJ30EETA, VJ30ELETA 1993
Information:
Start By:a. remove fuel injection lines FLUID SPILLAGE CONTAINMENT Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "TOOLS AND SHOP PRODUCT GUIDE, NENG2500", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates. 1. Use Tool (F) and remove the shutdown solenoid (1). 2. Remove two bolts (2) and remove actuator solenoid (3) from the fuel injection pump housing.3. Remove two rack zero plugs (4).
Typical Example4. Push the rack servo (5) toward the rear of the engine. Install Tools (A) in the rack zero pin holes. Push the rack servo (5) toward front of the engine and install Tool (B) to hold the rack against the rack zero pin. 5. Use Tool (C) to loosen bushing (6). 6. Install Tool (E) and compress fuel pump spring. Hold Tool (E) in position and remove bushing (6).
Typical Example7. Remove fuel injection pump with Tool (D).
When injection pumps, spacers and lifters are removed from the injection pump housing, keep the parts of each pump together so they can be installed back in their original location.
8. Disassemble the fuel injection pump. Remove ring (8). Make a separation of bonnet (7) from the plunger and barrel assembly (9).
Be careful when the injection pumps are disassembled. Do not cause damage to the surface on the plunger. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump in the barrel of another pump. If one part has wear, install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
9. Remove the gear segment, washer and spring from the barrel.10. Remove the ring, spring, collar and valve from the barrel.
Typical Example11. Remove spacer (10).Install Fuel Injection Pumps
Typical Example Make sure the fuel racks are in the center (zero) position before the fuel injection pumps are installed.1. Install plunger (10) and gear segment (11), washer (5) and spring (9) on barrel (4). Put check valve assembly (7), spring (3) and collar (8) in position in bonnet (6). Connect bonnet (6) and barrel (4) together with ring (2). Keep seal (1) with bonnet for use at installation. 2. Put spacer (13) into position in the pump housing bore. Make sure the correct spacer is with each pump.3. Put the space in gear segment (11) in alignment with the groove in barrel (4).4. Put the injection pump straight down into the housing bore so the space in gear segment (11) is in alignment with pin (12) and the groove in barrel (4) is in alignment with dowel (14). Use Tool (C) to install the pump. 5. Install seal (1) and bushing (16) in the pump housing bore. If the pump is in the correct position, install Tool (D) with bushing (16). Compress fuel injection pump spring with Tool (D) and hand start the bushing threads into the pump housing. Tighten the bushing to a torque of 163 14 N m (120 10 lb ft) with Tool (B).6. Check for correct installation of the injection pumps with the engine stopped. See the topic "Injection Pump Installation" in Testing & Adjusting.
If one or more of the injection pumps have been installed wrong, damage to the engine is possible if cautions are not taken when the engine is first started. Make preparation to close off the air intake to stop the engine if necessary.
7. Remove Tool (A) and install the plug in the injection pump housing.End By:a. install fuel injection lines
Typical Example4. Push the rack servo (5) toward the rear of the engine. Install Tools (A) in the rack zero pin holes. Push the rack servo (5) toward front of the engine and install Tool (B) to hold the rack against the rack zero pin. 5. Use Tool (C) to loosen bushing (6). 6. Install Tool (E) and compress fuel pump spring. Hold Tool (E) in position and remove bushing (6).
Typical Example7. Remove fuel injection pump with Tool (D).
When injection pumps, spacers and lifters are removed from the injection pump housing, keep the parts of each pump together so they can be installed back in their original location.
8. Disassemble the fuel injection pump. Remove ring (8). Make a separation of bonnet (7) from the plunger and barrel assembly (9).
Be careful when the injection pumps are disassembled. Do not cause damage to the surface on the plunger. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump in the barrel of another pump. If one part has wear, install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
9. Remove the gear segment, washer and spring from the barrel.10. Remove the ring, spring, collar and valve from the barrel.
Typical Example11. Remove spacer (10).Install Fuel Injection Pumps
Typical Example Make sure the fuel racks are in the center (zero) position before the fuel injection pumps are installed.1. Install plunger (10) and gear segment (11), washer (5) and spring (9) on barrel (4). Put check valve assembly (7), spring (3) and collar (8) in position in bonnet (6). Connect bonnet (6) and barrel (4) together with ring (2). Keep seal (1) with bonnet for use at installation. 2. Put spacer (13) into position in the pump housing bore. Make sure the correct spacer is with each pump.3. Put the space in gear segment (11) in alignment with the groove in barrel (4).4. Put the injection pump straight down into the housing bore so the space in gear segment (11) is in alignment with pin (12) and the groove in barrel (4) is in alignment with dowel (14). Use Tool (C) to install the pump. 5. Install seal (1) and bushing (16) in the pump housing bore. If the pump is in the correct position, install Tool (D) with bushing (16). Compress fuel injection pump spring with Tool (D) and hand start the bushing threads into the pump housing. Tighten the bushing to a torque of 163 14 N m (120 10 lb ft) with Tool (B).6. Check for correct installation of the injection pumps with the engine stopped. See the topic "Injection Pump Installation" in Testing & Adjusting.
If one or more of the injection pumps have been installed wrong, damage to the engine is possible if cautions are not taken when the engine is first started. Make preparation to close off the air intake to stop the engine if necessary.
7. Remove Tool (A) and install the plug in the injection pump housing.End By:a. install fuel injection lines
Parts engine JOHNSON:
0433392
0433392 ENGINE COVER, Lower
BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25EECE, BJ25EEDM, BJ25EEED, BJ25EEUB, BJ25ELSIC, BJ25ELSSS, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, BJ30EECS, BJ30EEDE, BJ30EEEC, BJ30EEUD, BJ30E
0284059
0284059 ENGINE COVER ASSY.
J20EEIE, J20EEND, J20EETS, J25EEID, J25EENS, J25EETC, J30EEIC, J30EENR, J30EETA
0434555
0434555 ENGINE COVER ASSY.
J20EEIE, J20EEND, J20EETS, J25EEID, J25EENS, J25EETC, J30EEIC, J30EENR, J30EETA
0284129
0284129 ENGINE COVER ASSY.
J20EEND, J20EERC, J20EETS, J25EENS, J25EERR, J25EETC, J25TEEND, J25TEERC, J25TEETS, J30EENR, J30EERM, J30EETA, J30TEENR, J30TEERM, J30TEETA
0284130
0284130 ENGINE COVER ASSY.
J20EEND, J20EERC, J20EETS, J25EENS, J25EERR, J25EETC, J25TEEND, J25TEERC, J25TEETS, J30EENR, J30EERM, J30EETA, J30TEENR, J30TEERM, J30TEETA
0435150
0435150 ENGINE COVER ASSY.
J20EEND, J20EEOR, J20EERC, J20EETS, J25EENS, J25EEOA, J25EERR, J25EETC, J30EENR, J30EEOB, J30EERM, J30EETA
0435155
0435155 ENGINE COVER ASSY.
BJ20SEEDA, BJ25EEDM, BJ30EEDE, HJ25TELEDA, J20EEND, J20EEOR, J20EERC, J20EETS, J25EENS, J25EEOA, J25EERR, J25EETC, J25TEEND, J25TEEOR, J25TEERC, J25TEETS, J25TELERC, J30EENR, J30EEOB, J30EERM, J30EETA, J30TEEDE, J30TEENR, J30TEEOB, J30TEERM, J30TEETA
0435152
0435152 ENGINE COVER ASSY.
BJ20SEEDA, BJ25EEDM, BJ30EEDE, HJ25TELEDA, J20EEND, J20EEOR, J20EERC, J20EETS, J25EENS, J25EEOA, J25EERR, J25EETC, J25TEEND, J25TEEOR, J25TEERC, J25TEETS, J25TELERC, J30EENR, J30EEOB, J30EERM, J30EETA, J30TEEDE, J30TEENR, J30TEEOB, J30TEERM, J30TEETA