0284715 JOHNSON ENGINE COVER ASSY.


0284715 ENGINE COVER ASSY. JOHNSON BJ20SEEDA, BJ20SEEUM, BJ25EEDM, BJ25EEUB, BJ30EEDE, BJ30EEUD, HJ25TELEDA, J20EEOR, J25EEOA, J25TEEOR, J25TEEUM, J30EEOB, J30TEEDE, J30TEEOB, J30TEEUD ENGINE
0284715 ENGINE COVER ASSY. JOHNSON
Rating:
38

Buy ENGINE COVER ASSY. 0284715 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

BRP JOHNSON entire parts catalog list:

BJ20SEEDA, BJ20SELEDA 1996
BJ20SEEUM, BJ20SELEUM 1997
BJ25EEDM, BJ25ELEDM, BJ25EREDC, BJ25ERLEDC, J25EEDM, J25ELEDM 1996
BJ25EEUB, BJ25ELEUB, J25EEUB, J25ELEUB 1997
BJ30EEDE, BJ30ELEDE, J30EEDE, J30ELEDE, SJ30EEDE 1996
BJ30EEUD, BJ30ELEUD, J30EEUD, J30ELEUD 1997
HJ25TELEDA, J25TEEDA, J25TELEDA, SJ25TEEDA 1996
J20EEOR, J20ELEOR 1995
J25EEOA, J25ELEOA 1995
J25TEEOR, J25TELEOR 1995
J25TEEUM, J25TELEUM, SJ25TEEUM 1997
J30EEOB, J30ELEOB 1995
J30TEEDE, J30TELEDE 1996
J30TEEOB, J30TELEOB 1995
J30TEEUD, J30TELEUD, SJ30TEEUD 1997

Information:

1. Disconnect tube assembly (1) at the fitting in the cylinder block.2. Remove bolts (2) that hold the flywheel housing to the cylinder block. 3. Install tooling (A) on each side of the flywheel housing (3). Use washers as needed to make tooling (A) straight. Fasten a hoist to tooling (A).4. Remove bolt (4) that holds the shaft in place.5. Remove bolts (5) that hold the flywheel housing to the cylinder block. Remove flywheel housing (3). The weight is 115 lb. (52 kg).Install Flywheel Housing
1. Thoroughly clean the contact surfaces of the cylinder block and flywheel housing. Install a new gasket on the cylinder block.2. Install two 1/2"-13 NC guide pins 180° apart in the cylinder block. 3. Install tooling (A) on each side of the flywheel housing. Use washers as needed to make tooling (A) straight. Fasten a hoist.4. Put flywheel housing (1) in position on the cylinder block. 5. Install the bolts that hold the flywheel housing to the cylinder block. Tighten bolts 1 through 8 in number sequence to a torque of 100 11 lb.ft. (135 15 N m). Tighten bolts 9 through 17 in number sequence to a torque of 41 5 lb.ft. (55 7 N m). Tighten bolts 1 through 8 in number sequence again to a torque of 100 11 lb.ft. (135 15 N m). Tighten bolts 9 through 17 in number sequence again to a torque of 41 5 lb.ft. (55 7 N m).6. Install the bolt that holds shaft (2) in place to the cylinder block. Tighten the bolt to a torque of 100 10 lb.ft. (135 14 N m). 7. Connect tube assembly (3).end by:a) install oil panb) install electric starting motorc) install flywheelDisassemble Flywheel Housing
start by:a) remove flywheel housing 1. Remove the bolts and nuts that hold adapter (1) in place. Remove adapter (1). 2. Remove bearing cup (2) from adapter (1). Remove O-ring seal (3). 3. Remove gear assembly (4) from the flywheel housing. 4. Remove bearing cone (5) from each side of the gear assembly with tooling (A). 5. Remove bearing cup (6) from the flywheel housing. 6. Remove the bolt from shaft (7). Remove shaft (7) with tooling (B).7. Remove the O-ring seals from the shaft. 8. Remove gear assembly (8) from the flywheel housing. 9. Remove bearing cone (9), spacer (10) and bearing cone (12) from gear (11). 10. Remove bearing cup (13), spacer (14) and bearing cup (15) from gear (11). Remove the ring from gear (11).Assemble Flywheel Housing
1. Inspect the O-ring seals and ports for damage and make replacements if needed. 2. Install the ring in gear (1). Install spacer (2) in the gear.3. Lower the temperature of bearing cups (3) and (4). Install bearing cup (3) and (4) in the gear. 4. Install bearing cone (7), spacer (6) and bearing cone (5) in gear (1). 5. Install gear assembly (8) in the flywheel housing. 6. Install O-ring seals (9) on shaft (10). Put clean oil on the seals. Make an alignment of the holes in the shaft with the holes in the flywheel housing and install shaft (10). Install one of the bolts to a torque of 100 10 lb.ft. (135 14 N m). 7. Lower the temperature of bearing cup (11). Install bearing cup (11). 8. Heat bearing cones (12) to a maximum temperature of 275°F (135°C). Install bearing cones (12) on gear (13). 9. Install gear assembly (14) in the flywheel housing. 10. Lower the temperature of bearing cone (15). Install bearing cone (15) in adapter (17).11. Install O-ring seal (16) on adapter (17). Put clean oil on the O-ring seal. 12. Install adapter (17) on the flywheel housing.end by:a) install flywheel housing


Parts engine JOHNSON:

0433392
ENGINE COVER, Lower
0433392 ENGINE COVER, Lower
BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25EECE, BJ25EEDM, BJ25EEED, BJ25EEUB, BJ25ELSIC, BJ25ELSSS, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, BJ30EECS, BJ30EEDE, BJ30EEEC, BJ30EEUD, BJ30E
0435152
ENGINE COVER ASSY.
0435152 ENGINE COVER ASSY.
BJ20SEEDA, BJ25EEDM, BJ30EEDE, HJ25TELEDA, J20EEND, J20EEOR, J20EERC, J20EETS, J25EENS, J25EEOA, J25EERR, J25EETC, J25TEEND, J25TEEOR, J25TEERC, J25TEETS, J25TELERC, J30EENR, J30EEOB, J30EERM, J30EETA, J30TEEDE, J30TEENR, J30TEEOB, J30TEERM, J30TEETA
0284714
 
0284714 ENGINE COVER ASSY.
BJ20SEEDA, BJ20SEEUM, BJ25EEDM, BJ25EEUB, BJ30EEDE, BJ30EEUD, HJ25TELEDA, J20EEOR, J25EEOA, J25TEEOR, J25TEEUM, J30EEOB, J30TEEDE, J30TEEOB, J30TEEUD
0284713
 
0284713 ENGINE COVER ASSY.
BJ20SEEDA, BJ20SEEUM, BJ25EEDM, BJ25EEUB, BJ30EEDE, BJ30EEUD, J20EEOR, J25EEOA, J30EEOB
0284396
 
0284396 ENGINE COVER ASSY.
J20EEOR, J25EEOA, J30EEOB
0284133
 
0284133 ENGINE COVER ASSY.
J20EEOR, J25EEOA, J30EEOB
0437188
 
0437188 ENGINE COVER ASSY.
BJ20SEEDA, BJ25EEDM, BJ30EEDE, HJ25TELEDA, J20EEOR, J25EEOA, J25TEEOR, J30EEOB, J30TEEDE, J30TEEOB
0438334
 
0438334 ENGINE COVER ASSY.
BJ20SEECB, BJ20SEEUM, BJ25EECE, BJ25EEUB, BJ30EECS, BJ30EEUD, J25TEECB, J25TEEUM, J30TEECS, J30TEEUD
Back to top