0396983 JOHNSON ENGINE COVER, Lower


0396983 ENGINE COVER, Lower JOHNSON J20CRCCA, J20CRCDC, J20CRCUR, J25ECCM, J25ECDR, J25ECUA, J30ECCE, J30ECDM, J30ECUB, J35RCCE, J35RCDM, J35RCUB ENGINE

Buy ENGINE COVER, Lower 0396983 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 20
 

BRP JOHNSON entire parts catalog list:

J20CRCCA, J20CRLCCA, J20ECCA, J20ELCCA 1988
J20CRCDC, J20CRLCDC, J20ECDC, J20ELCDC, J20TECDC 1986
J20CRCUR, J20CRLCUR, J20ECUR, J20ELCUR 1987
J25ECCM, J25ELCCM, J25RCCA, J25RLCCA, J25TECCA, J25TELCCA 1988
J25ECDR, J25ELCDR, J25RCDC, J25RDC, J25RLCDC, J25TECDC, J25TELCDC 1986
J25ECUA, J25ELCUA, J25RCUR, J25RLCUR, J25TECUR, J25TELCUR 1987
J30ECCE, J30ELCCE, J30RCCE, J30RLCCE, J30TECCE, J30TELCCE 1988
J30ECDM, J30ELCDM, J30RCDM, J30RLCDM, J30TECDM, J30TELCDM 1986
J30ECUB, J30ELCUB, J30RCUB, J30RLCUB, J30TECUB, J30TELCUB 1987
J35RCCE, J35RLCCE 1988
J35RCDM, J35RLCDM 1986
J35RCUB, J35RLCUB 1987

Information:


If no oil pressure is indicated, STOP the engine. If maximum coolant temperature is exceeded, STOP the engine. Engine damage can result.
Engine Oil Pressure - The oil pressure should be greatest after a cold engine is started. The typical engine oil pressure with SAE10W40 is 350 to 450 kPa ( 50 to 65 psi) at rated rpm.A lower oil pressure is normal at low idle. If the load is stable and the gauge reading changes, perform the following procedure:
Remove the load.
Stop the engine.
Check and maintain the oil level.
Jacket Water Coolant Temperature - Typical temperature range is 83° to 95°C (181.4° to 171°F). The maximum allowable temperature at sea level with the pressurized cooling system at 48 kPa (7 psi) is 103 °C (217.4 °F). Higher temperatures may occur under certain conditions. The water temperature reading may vary according to load. The temperature reading should never exceed 7 °C (44.6 °F) below the boiling point for the pressurized system that is being used.A 100 kPa (14.5 psi) radiator cap may be installed on the cooling system. The temperature of this cooling system must not exceed 112 °C (233.6 °F).If the engine is operating above the normal range and steam becomes apparent, perform the following procedure:
Reduce the load and the engine rpm.
Determine if the engine must be shut down immediately or if the engine can be cooled by reducing the load.
Inspect the cooling system for leaks.
Tachometer - This gauge indicates engine speed (rpm). When the throttle control lever is moved to the full throttle position without load, the engine is running at high idle. The engine is running at the full load rpm when the throttle control lever is at the full throttle position with maximum rated load.
To help prevent engine damage, never exceed the high idle rpm. Overspeeding can result in serious damage to the engine. Operation at speeds exceeding high idle rpm should be kept to a minimum.
Ammeter - This gauge indicates the amount of charge or discharge in the battery charging circuit. Operation of the indicator should be to the "+" side of "0" (zero).
Fuel Level - This gauge indicates the fuel level in the fuel tank. The fuel level gauge operates when the "START/STOP" switch is in the "on" position.
Service Hour Meter - The gauge indicates total operating hours of the engine.Indicator Lamps
There are four main indicator lamps that are available.
Shutdown Lamp
Warning Lamp
Wait to Start Lamp (Glow Plug Warning Lamp)
Low Oil Pressure LampFor information, refer to this manual, "Monitoring System (Table for the Indicator Lamps)" for the sequence of operation of the shutdown lamp and the warning lamp.The function of the wait to start lamp is automatically controlled at engine start-up.The function of the low oil pressure lamp is controlled by the engine ECM. If low oil pressure is detected, the lamp will be illuminated. The reason for the illumination of the low-pressure lamp should be investigated immediately.All lamps will illuminate for 2 seconds in order to check that the lamps are functioning when the keyswitch is turned to the ON position. If any of the lamps stay illuminated, the reason for illumination should be investigated immediately.The glow plug warning lamp will flash in order to show that the engine is been held at low speed. This function will be performed at engine starting and the duration will depend on ambient temperature and engine temperature.Instrument panels and Displays
In order to monitor the engine a wide verity of instrument panels are available. These instrument panels can contain the indicator lamps and the gauges for the application. Also available are mini power displays and performance monitors. These displays and monitors can show the operator the following engine information.
The system configuration parameters
The customer specified parameters
Diagnostic codes
Event codes
Coolant temperature
Oil temperature
Oil pressure
Intake temperature
Intake pressure
Fuel temperature


Parts engine JOHNSON:

0282667
 
0282667 ENGINE COVER ASSY.
J20CRCDC, J25ECDR
0282666
 
0282666 ENGINE COVER ASSY.
J20CRCDC, J25ECDR
0282665
 
0282665 ENGINE COVER ASSY.
J20CRCDC, J25ECDR
0282664
 
0282664 ENGINE COVER ASSY.
J20CRCDC, J25ECDR
0396175
0283050
 
0283050 ENGINE COVER ASSY.
J20CRCCA, J20CRCUR, J25ECCM, J25ECUA
0283051
ENGINE COVER ASSY.
0283051 ENGINE COVER ASSY.
J20CRCCA, J20CRCUR, J25ECCM, J25ECUA
0283052
 
0283052 ENGINE COVER ASSY.
J20CRCCA, J20CRCUR, J25ECCM, J25ECUA
Back to top