0432579 ENGINE COVER ASSY., 225 JOHNSON
J185ESXESS, J185ESXW, J200CXCEA, J200CXESM, J225CXCED, J225CXESS
ENGINE
Price: query
Rating:
Number on catalog scheme: 1
BRP JOHNSON entire parts catalog list:
J185ESXW 1989
J200CXCEA, J200STLCEB, J200TXCEA, TJ200TXCEA 1989
J200CXESM, J200STLESE, J200TXESM, VJ200SLESE, VJ200TXESM 1990
J225CXCED, J225PLAED, J225PLCED, J225PXCED, J225TLAED, J225TLCED, J225TXCED 1989
J225CXESS, J225PLASS, J225PLESS, J225PXESS, J225TLASS, J225TLESS, J225TXESS, VJ225PLESS, VJ225PXESS, VJ225TLASS, VJ225TLESS, VJ225TXESS 1990
Information:
Recommended Actions
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 1
Troubleshooting Test Steps Values Results
1. Diagnostic Codes
A. Download the Histograms before performing any troubleshooting or clearing any diagnostic codes.
Note: The downloaded information will be required by the Dealer Solutions Network (DSN) if troubleshooting assistance is needed.
B. Use the electronic service tool to check for active or logged codes.
Diagnostic codes
Result: A diagnostic code is present.
Repair: Troubleshoot the code and then reset the histogram. Refer to Troubleshooting, Diagnostic Trouble Codes or Troubleshooting, Event Codes.
Result: A diagnostic code is not present.
Proceed to Test Step 2.
2. Visible Faults
A. Check that the fuel supply valve (if equipped) is in the OPEN position.
B. Check for the correct level of fuel, oil, and coolant.
C. Check for water in the primary fuel filter/water separator.
D. If the ambient temperature is below 0 °C (32 °F), check the specification of engine oil and oil for the machine.
E. Visually inspect the engine for the following faults:
Missing components
Damaged components
Damaged electrical cables or loose electrical cables
Oil leaks
Fuel leaks
All fuel filters are correctly installed.
F. Check that the battery voltage is correct.
G. Use the electronic service tool to check the average cranking speed of the engine.
Visible faults
Result: The fuel supply valve (if equipped) is not in the OPEN position.
Repair: Move the fuel supply valve to the OPEN position.
Result: The level of fuel, oil, or coolant is not correct.
Repair: Replenish any fluids with an incorrect level.
Result: Water is present in the primary fuel filter/water separator.
Repair: Drain any water from the primary fuel filter/water separator.
Result: The correct specification of engine oil and oil for the machine is not in use.
Repair: Replenish the system with oil of the correct specification
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 1
Troubleshooting Test Steps Values Results
1. Diagnostic Codes
A. Download the Histograms before performing any troubleshooting or clearing any diagnostic codes.
Note: The downloaded information will be required by the Dealer Solutions Network (DSN) if troubleshooting assistance is needed.
B. Use the electronic service tool to check for active or logged codes.
Diagnostic codes
Result: A diagnostic code is present.
Repair: Troubleshoot the code and then reset the histogram. Refer to Troubleshooting, Diagnostic Trouble Codes or Troubleshooting, Event Codes.
Result: A diagnostic code is not present.
Proceed to Test Step 2.
2. Visible Faults
A. Check that the fuel supply valve (if equipped) is in the OPEN position.
B. Check for the correct level of fuel, oil, and coolant.
C. Check for water in the primary fuel filter/water separator.
D. If the ambient temperature is below 0 °C (32 °F), check the specification of engine oil and oil for the machine.
E. Visually inspect the engine for the following faults:
Missing components
Damaged components
Damaged electrical cables or loose electrical cables
Oil leaks
Fuel leaks
All fuel filters are correctly installed.
F. Check that the battery voltage is correct.
G. Use the electronic service tool to check the average cranking speed of the engine.
Visible faults
Result: The fuel supply valve (if equipped) is not in the OPEN position.
Repair: Move the fuel supply valve to the OPEN position.
Result: The level of fuel, oil, or coolant is not correct.
Repair: Replenish any fluids with an incorrect level.
Result: Water is present in the primary fuel filter/water separator.
Repair: Drain any water from the primary fuel filter/water separator.
Result: The correct specification of engine oil and oil for the machine is not in use.
Repair: Replenish the system with oil of the correct specification
Parts engine JOHNSON:
0583282
0583282 ENGINE CABLE ASSY.
J185ESXESS, J185ESXW, J200CXCCR, J200CXCEA, J200CXESM, J225CXCCE, J225CXCED, J225CXESS
0283899
0283669
0283669 ENGINE COVER ASSY., 200
J185ESXESS, J185ESXW, J200CXCEA, J200CXEIB, J200CXESM, J225CXCED, J225CXEIC, J225CXESS
0283626
0283626 ENGINE COVER ASSY., 200TX
J185ESXESS, J185ESXW, J200CXCEA, J200CXEIB, J200CXESM, J225CXCED, J225CXEIC, J225CXESS
0283773
0283630
0283630 ENGINE COVER ASSY., 225
J185ESXESS, J185ESXW, J200CXCEA, J200CXEIB, J200CXESM, J225CXCED, J225CXEIC, J225CXESS
0432457
0432466