0435149 JOHNSON ENGINE COVER ASSY.


0435149 ENGINE COVER ASSY. JOHNSON HJ20CREDA, HJ25RLEDA, HJ30REDE, J20CREND, J20CREOR, J20CRERC, J20CRETS, J25REND, J25REOR, J25RERC, J25RETS, J30RENR, J30REOB, J30RERM, J30RETA, J35RENR, J35RERM, J35RETA, SJ35REDE ENGINE
0435149 ENGINE COVER ASSY. JOHNSON
Rating:
78

Buy ENGINE COVER ASSY. 0435149 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

BRP JOHNSON entire parts catalog list:

HJ20CREDA, HJ20CRLEDA, J20CREDA, J20CRLEDA 1996
HJ25RLEDA, J25REDA, J25RLEDA, SJ25REDA, SJ25RLEDA 1996
HJ30REDE, HJ30RLEDE, J30REDE, J30RLEDE, SJ30REDE, SJ30RLEDE 1996
J20CREND, J20CRLEND, TJ20CREND, TJ20CRLEND 1992
J20CREOR, J20CRLEOR 1995
J20CRERC, J20CRLERC 1994
J20CRETS, J20CRLETS, TJ20CRETS, TJ20CRLETS 1993
J25REND, J25RLEND 1992
J25REOR, J25RLEOR 1995
J25RERC, J25RLERC 1994
J25RETS, J25RLETS 1993
J30RENR, J30RLENR 1992
J30REOB, J30RLEOB 1995
J30RERM, J30RLERM 1994
J30RETA, J30RLETA 1993
J35RENR, J35RLENR 1992
J35RERM, J35RLERM 1994
J35RETA, J35RLETA 1993
SJ35REDE, SJ35RLEDE 1996

Information:

Start By:a. remove valve covers Call out (1) and (2) are not used in this removal procedure. Call outs begin with number (3). 1. Remove bolts (3) that hold the valve cover bases to the cylinder head assembly. Remove valve cover bases (4).
To prevent damage to the fuel injection nozzle, hold adapter assembly (5) in position at the end of the injection nozzle (6) when fuel line nut (7) is loosened or tightened.
2. Use Tool (A) and a 5P-0328 Crow Foot (7/8 in)to loosen the fuel injection line nut at the nozzle end. 3. Use Tool (B) to loosen the nut at the fuel injection line adapter end. Remove inner fuel injection lines (8). Install caps and plugs on all fuel injection line openings to keep dirt out of the fuel system. 4. Remove bolts (9) that hold the rocker shaft assemblies to the cylinder head assembly.5. Remove rocker shaft assemblies (10). 6. Put identification marks on the push rods as to their location in the engine. Remove push rods (11). 7. Put identification marks on the bridges as to their location in the engine. Remove bridges (12) from the dowels on the cylinder head assembly.Install Rocker Shaft Assemblies & Push Rods 1102 & 1208-012
1. Put clean engine oil on the bridges and dowels. Install the original bridges in their respective locations. New bridges can be mixed.2. Install bridges (1) on the bridge dowels. While firmly pressing 0.5 to 4.5 kg (1 to 10 lb)straight down on the top contact surface of the bridge, turn the adjusting screw clockwise until contact is made with the valve stem. Turn the screw an additional 20 to 30 degrees (1/3 to 1/2 of 1 hex on nut).This will straighten the dowel in the guide and compensate for the slack in the threads. Hold the adjusting screw in this position and tighten the locknut to a torque of 30 4 N m (22 3 lb ft). Install the original push rods in their respective locations in the engine. New push rods can be mixed.3. Install push rods (2). 4. Put rocker shaft assemblies (3) in position on the cylinder head assembly.5. Put clean engine oil on the threads of the bolts that hold the rocker shaft assemblies in place. Tighten the bolts first to a torque of 270 25 N m (200 18 lb ft).Start with the bolt in the center of the rocker shaft assembly. Tighten the bolts again to a torque of 450 20 N m (330 15 lb ft).Tighten the bolts again by hand to a torque of 450 20 N m (330 15 lb ft).
Do not cause damage to the O-ring seals on the inner fuel lines.
6. Install inner fuel injection lines (4). Tighten the fuel injection line adapter nuts (5) to a torque of 40 7 N m (30 5 lb ft)with Tool (A).
Do not let the tops of the fuel nozzles turn when the fuel lines are tightened. The nozzles will be damaged if the top of the nozzles turns in the body.
7. Tighten fuel injection line nut (6) to a torque of 40 7 N m (30 5 lb ft)with Tool (B) and a 5P-0328 (7/8 in) Crow Foot wrench.8. Make adjustments to the valves until the intake valve clearance is 0.38 mm (.015 in)and the exhaust valve clearance 0.76 mm (.030 in).See the topic "Valve Clearance Setting" in Systems Operation Testing & Adjusting Manual. Tighten the locknut to a torque of 30 4 N m (22 3 lb ft)and check the adjustments. 9. Install valve cover bases (7) on the cylinder head assembly. Install bolts that hold the valve cover bases in place. Tighten the bolts to a torque of 14 3 N m (10 2 lb ft).End By:a. install valve covers


Parts engine JOHNSON:

0433392
ENGINE COVER, Lower
0433392 ENGINE COVER, Lower
BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25EECE, BJ25EEDM, BJ25EEED, BJ25EEUB, BJ25ELSIC, BJ25ELSSS, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, BJ30EECS, BJ30EEDE, BJ30EEEC, BJ30EEUD, BJ30E
0284058
 
0284058 ENGINE COVER ASSY.
J20CREIE, J20CREND, J20CRETS, J25REIE, J25REND, J25RETS, J30REIC, J30RENR, J30RETA, J35REIC, J35RENR, J35RETA
0283875
 
0283875 ENGINE COVER ASSY.
J20CREND, J20CRERC, J20CRETS, J25REND, J25RERC, J25RETS, J30RENR, J30RERM, J30RETA, J35RENR, J35RERM, J35RETA
0284127
 
0284127 ENGINE COVER ASSY.
J20CREND, J20CRERC, J20CRETS, J25REND, J25RERC, J25RETS, J30RENR, J30RERM, J30RETA, J35RENR, J35RERM, J35RETA
0284026
ENGINE COVER ASSY.
0284026 ENGINE COVER ASSY.
J20CREND, J20CRERC, J20CRETS, J25REND, J25RERC, J25RETS, J30RENR, J30RERM, J30RETA, J35RENR, J35RERM, J35RETA
0283871
 
0283871 ENGINE COVER ASSY.
J20CREND, J20CRERC, J20CRETS, J25REND, J25RERC, J25RETS, J30RENR, J30RERM, J30RETA, J35RENR, J35RERM, J35RETA
0437186
 
0437186 ENGINE COVER ASSY.
HJ20CREDA, HJ25RLEDA, HJ30REDE, J20CREOR, J25REOR, J30REOB, SJ35REDE
0437184
 
0437184 ENGINE COVER ASSY.
BJ20SREDA, BJ25BAEDR, BJ30BAEDE, HJ20CREDA, HJ25RLEDA, HJ30REDE, J20CREOR, J25REOR, J30REOB, SJ35REDE
Back to top