0435151 JOHNSON ENGINE COVER ASSY.


0435151 ENGINE COVER ASSY. JOHNSON BJ20SREDA, BJ25BAEDR, BJ30BAEDE, HJ20CREDA, HJ25RLEDA, HJ30REDE, J20CREND, J20CREOR, J20CRERC, J20CRETS, J25REND, J25REOR, J25RERC, J25RETS, J30RENR, J30REOB, J30RERM, J30RETA, J35RENR, J35RERM, J35RETA, SJ35REDE ENGINE
0435151 ENGINE COVER ASSY. JOHNSON
Rating:
93

Buy ENGINE COVER ASSY. 0435151 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$58.99
 

18-01-2022
0.1[0.00] Pounds
-: -
Meiko 0435151 Traction Cable
Genuine oem replacement part || Meiko manufactures ware washers for commercial clients ranging from small dishwashers to the biggest wash-up system in the world. || Use genuine oem parts for safety reliability and performance
Number on catalog scheme: 1
 

BRP JOHNSON entire parts catalog list:

BJ20SREDA, BJ20SRLEDA 1996
BJ25BAEDR, BJ25BALEDR, BJ25BREDC, BJ25BRLEDC, HJ25RAEDA, SJ25RDEDC 1996
BJ30BAEDE, BJ30BALEDE 1996
HJ20CREDA, HJ20CRLEDA, J20CREDA, J20CRLEDA 1996
HJ25RLEDA, J25REDA, J25RLEDA, SJ25REDA, SJ25RLEDA 1996
HJ30REDE, HJ30RLEDE, J30REDE, J30RLEDE, SJ30REDE, SJ30RLEDE 1996
J20CREND, J20CRLEND, TJ20CREND, TJ20CRLEND 1992
J20CREOR, J20CRLEOR 1995
J20CRERC, J20CRLERC 1994
J20CRETS, J20CRLETS, TJ20CRETS, TJ20CRLETS 1993
J25REND, J25RLEND 1992
J25REOR, J25RLEOR 1995
J25RERC, J25RLERC 1994
J25RETS, J25RLETS 1993
J30RENR, J30RLENR 1992
J30REOB, J30RLEOB 1995
J30RERM, J30RLERM 1994
J30RETA, J30RLETA 1993
J35RENR, J35RLENR 1992
J35RERM, J35RLERM 1994
J35RETA, J35RLETA 1993
SJ35REDE, SJ35RLEDE 1996

Information:

Start By:a. remove oil pump1. Check the connecting rods and caps for their identification and location. 2. Turn the crankshaft until the connecting rod caps are in position.3. Remove two bolts (1) and the cap from the connecting rod. Remove the lower half of the bearing from the cap.4. Push the connecting rod away from the crankshaft. Remove the upper half of the bearing from the connecting rod. Install the bearings dry when the clearance checks are made. Put clean engine oil on the bearings for final assembly.5. Install the upper half of the bearing in the connecting rod.6. Pull the connecting rod slowly on to the crankshaft. 7. Install the lower half of the bearing in the cap. Be sure the tabs in the back of bearings are in the tab grooves of the connecting rod and cap. The serviceman must be very careful to use Plastigage, Tool (A) correctly. The following points must be remembered:... Make sure that the backs of the bearings and the bores are clean and dry.... Make sure that the bearing locking tabs are properly seated in their slots.... The crankshaft must be free of oil where the Plastigage touches it.... Put of a piece of Plastigage (A) on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.... Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.... Do not turn the crankshaft with the Plastigage installed. ... Carefully remove the cap but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements.... Remove the Plastigage before installing the cap.When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major widths to make sure that they are within the specification range. Also, experience has shown that when checking clearances tighter than 0.10 mm (.004 in) the readings may be low by 0.013 to 0.025 mm (.0005 to .0010 in).Out-of-round journals can give faulty readings. Also, journal taper may be indicated when one end of the Plastigage is wider that the other.For complete details concerning measuring bearing clearances, see the topic, "Engine Bearings & Crankshafts," SEBD0531. 8. Use Plastigage (A) to check the bearing clearance. 9. Put Plastigage (A) on the bearing.10. Put 2P-2506 Thread Lubricanton the threads of the rod bolts and seat surfaces of the nuts. Be sure the cylinder numbers on the rod cap and rod are the same and on the same side of connecting rod. Numbers are on the same side of the rod and cap as are the bearing tab slots. If new rods are installed, put the cylinder number on the rod and cap. Do not turn the crankshaft when Plastigage (A) is in position. Use Steps 13 and 14 for rods using through bolt design.
Do notuse an impact wrench to tighten the bolts the additional 90 5 degreesof a turn more.
11. Install rod caps (2). Install the two bolts. Tighten each bolt to a torque of 90 8 N m (67 6 lb ft). Put a mark on the nuts and cap, and tighten the nuts an extra 90 5 degrees from the mark. Remove the rod cap. Remove Plastigage (A), and check the bearing clearance. The bearing clearance must be 0.071 to 0.168 mm (.0028 to .0066 in) for new bearings. Maximum clearance with used bearings is 0.25 mm (.010 in).12. Put clean engine oil on lower half of the bearing. Install the rod cap again. Tighten each bolt to a torque of 90 8 N m (67 6 lb ft). Put a mark on the bolts and cap, and tighten the bolts an extra 90 5 degrees from the mark.13. Tighten each nut to a torque of 80 5 N m (59 4 lb ft). Tighten each nut an additional 120 5 degrees. Remove Plastigage (A), and check the bearing clearance. The bearing clearance must be 0.071 to 0.168 mm (.0028 to .0066 in) for new bearings. Maximum clearance with used bearings is 0.25 mm (.010 in).14. Lubricate bolt threads, nuts, bearing, and seating faces of cap with clean engine oil. Tighten each nut to a torque of 80 5 N m (59 4 lb ft). Put a mark on the nuts and cap, and tighten the nuts an extra 120 5 degrees from the mark.15. Do steps 1 through 14 (as appropriate) for the remainder of the connecting rod bearings.End By:a. Install oil pump


Parts engine JOHNSON:

0433392
ENGINE COVER, Lower
0433392 ENGINE COVER, Lower
BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25EECE, BJ25EEDM, BJ25EEED, BJ25EEUB, BJ25ELSIC, BJ25ELSSS, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, BJ30EECS, BJ30EEDE, BJ30EEEC, BJ30EEUD, BJ30E
0284058
 
0284058 ENGINE COVER ASSY.
J20CREIE, J20CREND, J20CRETS, J25REIE, J25REND, J25RETS, J30REIC, J30RENR, J30RETA, J35REIC, J35RENR, J35RETA
0283875
 
0283875 ENGINE COVER ASSY.
J20CREND, J20CRERC, J20CRETS, J25REND, J25RERC, J25RETS, J30RENR, J30RERM, J30RETA, J35RENR, J35RERM, J35RETA
0284127
 
0284127 ENGINE COVER ASSY.
J20CREND, J20CRERC, J20CRETS, J25REND, J25RERC, J25RETS, J30RENR, J30RERM, J30RETA, J35RENR, J35RERM, J35RETA
0284026
ENGINE COVER ASSY.
0284026 ENGINE COVER ASSY.
J20CREND, J20CRERC, J20CRETS, J25REND, J25RERC, J25RETS, J30RENR, J30RERM, J30RETA, J35RENR, J35RERM, J35RETA
0437186
 
0437186 ENGINE COVER ASSY.
HJ20CREDA, HJ25RLEDA, HJ30REDE, J20CREOR, J25REOR, J30REOB, SJ35REDE
0437184
 
0437184 ENGINE COVER ASSY.
BJ20SREDA, BJ25BAEDR, BJ30BAEDE, HJ20CREDA, HJ25RLEDA, HJ30REDE, J20CREOR, J25REOR, J30REOB, SJ35REDE
0437185
 
0437185 ENGINE COVER ASSY.
HJ20CREDA, HJ25RLEDA, HJ30REDE, J20CREOR, J25REOR, J30REOB, SJ35REDE
Back to top