0435154 JOHNSON ENGINE COVER ASSY.


0435154 ENGINE COVER ASSY. JOHNSON BJ20SREDA, BJ25BAEDR, BJ30BAEDE, HJ20CREDA, HJ25RLEDA, HJ30REDE, J20CREND, J20CREOR, J20CRERC, J20CRETS, J25REND, J25REOR, J25RERC, J25RETS, J30RENR, J30REOB, J30RERM, J30RETA, J35RENR, J35RERM, J35RETA, SJ35REDE ENGINE
0435154 ENGINE COVER ASSY. JOHNSON
Rating:
83

Buy ENGINE COVER ASSY. 0435154 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

BRP JOHNSON entire parts catalog list:

BJ20SREDA, BJ20SRLEDA 1996
BJ25BAEDR, BJ25BALEDR, BJ25BREDC, BJ25BRLEDC, HJ25RAEDA, SJ25RDEDC 1996
BJ30BAEDE, BJ30BALEDE 1996
HJ20CREDA, HJ20CRLEDA, J20CREDA, J20CRLEDA 1996
HJ25RLEDA, J25REDA, J25RLEDA, SJ25REDA, SJ25RLEDA 1996
HJ30REDE, HJ30RLEDE, J30REDE, J30RLEDE, SJ30REDE, SJ30RLEDE 1996
J20CREND, J20CRLEND, TJ20CREND, TJ20CRLEND 1992
J20CREOR, J20CRLEOR 1995
J20CRERC, J20CRLERC 1994
J20CRETS, J20CRLETS, TJ20CRETS, TJ20CRLETS 1993
J25REND, J25RLEND 1992
J25REOR, J25RLEOR 1995
J25RERC, J25RLERC 1994
J25RETS, J25RLETS 1993
J30RENR, J30RLENR 1992
J30REOB, J30RLEOB 1995
J30RERM, J30RLERM 1994
J30RETA, J30RLETA 1993
J35RENR, J35RLENR 1992
J35RERM, J35RLERM 1994
J35RETA, J35RLETA 1993
SJ35REDE, SJ35RLEDE 1996

Information:

1. Remove bolts (1) that hold the elbow in position on the oil pump. Remove bolt (2) and lock that fastens the suction bell to the oil pan plate.
The oil pump idler gear (5) can fall off the pump when the pump is removed. To prevent injury always hold gear on the pump when the pump is removed.
2. Bend the two tabs on the locks on the left hand side of the engine. Remove the four bolts (3) and (4) that fasten the oil pump to the cylinde block. Remove the oil pump and suction bell as a unit. The weight of the unit is 16 kg (35 lb.). Remove idler gear (5) from the oil pump.Install Oil Pump
1. Install idler gear (2) on the oil pump. Put the oil pump (1) in position on the cylinder block. Be sure idler gear (2) is engaged with the crankshaft gear and the tabs on locks on the left hand mounting bolts are not next to the oil pan gasket surface when the bolts are tightened. 2. Install bolts (3) that fasten the gasket and elbow to the oil pump.3. Install the lock and bolt (4) that hold the suction bell to the oil pan plate.END BY:a) install oil panDisassemble Oil Pump
START BY:a) remove oil pump 1. Remove idler gear (2). Remove bearing from gear with tooling (B).2. Remove suction bell (1).3. Remove the bolt and the washer from the oil pump drive gear. 4. Remove the drive gear from the shaft with tooling (A).5. Remove the key from the pump shaft.6. Remove bolts (3) from the pump body. 7. Remove body (8), two gears (7), keys and spacer (4) from the pump.8. Remove two shafts (5) and the gears.9. Remove bolts (6), the cover and the pressure relief valve from the body. 10. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with tooling (B). Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with tooling (A) and a press as follows:a) Put bearings (1) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing toward the outside of the pump body. Install the bearing until it is 1.52 mm (.060 in.) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30° 15° from the center line through the bores in the scavenge pump body and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores. 2. Install the bearings in oil pump body assembly with tooling (A) and a press as follows:a) Put bearings (2) in position on the inside of the oil pump body assembly with the chamfer on the bearings toward the outside of the pump body. Install the bearings until they are even with the outside of the pump body. Make sure the joints in the bearings are at an angle of 30° 15° from the centerline through the bearing bores and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See OIL PUMP in SPECIFICATIONS.4. Put clean engine oil on all the parts of the oil pump. 5. Install pressure relief valve (3), cover (4) and bolt (5) in the oil pump body assembly. 6. Install gears and shafts (6) in the oil pump body assembly.7. Install spacer (7) and the two keys in shafts (6). 8. Install two gears and scavenge pump body assembly (8).9. Install key (9), drive gear (11), the washer and bolt (10). Tighten the bolt to a torque of 43 7 N m (32 5 lb.ft.).10. Install the bearing in the idler gear with tooling (A) and a press until it is even with the outside surface of the gear.11. Install the idler gear and suction bell.
The oil pump must turn freely by hand after it is assembled.
END BY:a) install oil pump


Parts engine JOHNSON:

0433392
ENGINE COVER, Lower
0433392 ENGINE COVER, Lower
BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25EECE, BJ25EEDM, BJ25EEED, BJ25EEUB, BJ25ELSIC, BJ25ELSSS, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, BJ30EECS, BJ30EEDE, BJ30EEEC, BJ30EEUD, BJ30E
0284058
 
0284058 ENGINE COVER ASSY.
J20CREIE, J20CREND, J20CRETS, J25REIE, J25REND, J25RETS, J30REIC, J30RENR, J30RETA, J35REIC, J35RENR, J35RETA
0283875
 
0283875 ENGINE COVER ASSY.
J20CREND, J20CRERC, J20CRETS, J25REND, J25RERC, J25RETS, J30RENR, J30RERM, J30RETA, J35RENR, J35RERM, J35RETA
0284127
 
0284127 ENGINE COVER ASSY.
J20CREND, J20CRERC, J20CRETS, J25REND, J25RERC, J25RETS, J30RENR, J30RERM, J30RETA, J35RENR, J35RERM, J35RETA
0284026
ENGINE COVER ASSY.
0284026 ENGINE COVER ASSY.
J20CREND, J20CRERC, J20CRETS, J25REND, J25RERC, J25RETS, J30RENR, J30RERM, J30RETA, J35RENR, J35RERM, J35RETA
0437186
 
0437186 ENGINE COVER ASSY.
HJ20CREDA, HJ25RLEDA, HJ30REDE, J20CREOR, J25REOR, J30REOB, SJ35REDE
0437184
 
0437184 ENGINE COVER ASSY.
BJ20SREDA, BJ25BAEDR, BJ30BAEDE, HJ20CREDA, HJ25RLEDA, HJ30REDE, J20CREOR, J25REOR, J30REOB, SJ35REDE
0437185
 
0437185 ENGINE COVER ASSY.
HJ20CREDA, HJ25RLEDA, HJ30REDE, J20CREOR, J25REOR, J30REOB, SJ35REDE
Back to top