0435159 ENGINE COVER ASSY. JOHNSON
J48ESLEDC, J48ESLEDC, J48ESLENB, J48ESLENB, J48ESLEOS, J48ESLEOS, J48ESLERD, J48ESLERD, J48ESLETE, J48ESLETE
ENGINE
Price: query
Rating:
BRP JOHNSON entire parts catalog list:
- ENGINE COVER - JOHNSON » 0435159
J48ESLENB, VJ48ESLENB 1992
J48ESLENB, VJ48ESLENB 1992
J48ESLEOS 1995
J48ESLEOS 1995
J48ESLERD 1994
J48ESLERD 1994
J48ESLETE, TJ48ESLETE, VJ48ESLETE 1993
J48ESLETE, TJ48ESLETE, VJ48ESLETE 1993
Information:
1. Check each bearing cap (1) for its location on the engine. Each cap has an arrow which is toward the front of the block and a number which gives the location of that cap. Keep each bearing with the correct cap.2. Remove bearing caps No. 2 through No. 4. Remove thrust plates from No. 3 upper bearing.
Be careful not to cause damage to the crankshaft journals when the crankshaft is removed.
3. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft as shown. Remove No. 1 and No. 5 main bearing caps. Remove the crankshaft. Weight of the crankshaft is 122 kg (270 lb.). 4. Remove crankshaft gear (2) with tooling (A).5. Remove dowel and pin from crankshaft with tooling (B).Install Crankshaft
1. Install pin (1) in the crankshaft end until it is extended from the surface 6.4 0.5 mm (.25 .02 in.).2. Install dowel (2) until it is extended from the surface 4.1 0.5 mm (0.16 0.02 in.). 3. Heat crankshaft gear (3) to a maximum temperature of 232°C (450°F). Install gear (3) on the crankshaft with groove (4) in alignment with dowel (2).4. Make sure the upper main bearings are clean. Put clean oil on the upper main bearings and journals of the crankshaft.
Do not cause damage to the crankshaft journals. Make sure the "V" mark on the crankshaft gear is in alignment with the "V" mark on the idler gear.
5. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft and put it in position in the block. For more detail about installation of main bearings see REMOVE AND INSTALL CRANKSHAFT MAIN BEARINGS.6. Check the bearing clearance with Plastigage.7. Put clean engine oil on the bolts for caps No. 1 and No. 5. Install No. 1 and No. 5 caps with the bolts finger tight. Make sure the arrows on the caps are toward the front of the block. 8. Install thrust plates (5) for the No. 3 upper main bearing. Install the thrust plates with the side that has the identification "Block Side" toward the cylinder block.9. Put clean oil on the bolts for caps No. 2 through No. 4. Install caps No. 2 through No. 4 with the bolts finger tight. Make sure the arrows are toward the front of the block.10. Tighten the cap bolts as follows:a) Tighten the bolts on the tab end of the caps first to a torque of 260 14 N m (190 10 lb.ft.).b) Tighten the bolts on the other end of the caps to a torque of 260 14 N m (190 10 lb.ft.).c) Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120°. Tighten the bolts on the tab end of the cap 120°. 11. Check the play of the crankshaft with tool (A). Make sure the dial indicator is against a machined surface. End play for new thrust plates must be 0.15 to 0.51 mm (0.006 to 0.020 in.). The maximum end play with used thrust plates is 0.89 mm (0.035 in.).END BY:a) install pistonsb) install flywheel housingc) install timing gear coverd) install oil pump
Be careful not to cause damage to the crankshaft journals when the crankshaft is removed.
3. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft as shown. Remove No. 1 and No. 5 main bearing caps. Remove the crankshaft. Weight of the crankshaft is 122 kg (270 lb.). 4. Remove crankshaft gear (2) with tooling (A).5. Remove dowel and pin from crankshaft with tooling (B).Install Crankshaft
1. Install pin (1) in the crankshaft end until it is extended from the surface 6.4 0.5 mm (.25 .02 in.).2. Install dowel (2) until it is extended from the surface 4.1 0.5 mm (0.16 0.02 in.). 3. Heat crankshaft gear (3) to a maximum temperature of 232°C (450°F). Install gear (3) on the crankshaft with groove (4) in alignment with dowel (2).4. Make sure the upper main bearings are clean. Put clean oil on the upper main bearings and journals of the crankshaft.
Do not cause damage to the crankshaft journals. Make sure the "V" mark on the crankshaft gear is in alignment with the "V" mark on the idler gear.
5. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft and put it in position in the block. For more detail about installation of main bearings see REMOVE AND INSTALL CRANKSHAFT MAIN BEARINGS.6. Check the bearing clearance with Plastigage.7. Put clean engine oil on the bolts for caps No. 1 and No. 5. Install No. 1 and No. 5 caps with the bolts finger tight. Make sure the arrows on the caps are toward the front of the block. 8. Install thrust plates (5) for the No. 3 upper main bearing. Install the thrust plates with the side that has the identification "Block Side" toward the cylinder block.9. Put clean oil on the bolts for caps No. 2 through No. 4. Install caps No. 2 through No. 4 with the bolts finger tight. Make sure the arrows are toward the front of the block.10. Tighten the cap bolts as follows:a) Tighten the bolts on the tab end of the caps first to a torque of 260 14 N m (190 10 lb.ft.).b) Tighten the bolts on the other end of the caps to a torque of 260 14 N m (190 10 lb.ft.).c) Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120°. Tighten the bolts on the tab end of the cap 120°. 11. Check the play of the crankshaft with tool (A). Make sure the dial indicator is against a machined surface. End play for new thrust plates must be 0.15 to 0.51 mm (0.006 to 0.020 in.). The maximum end play with used thrust plates is 0.89 mm (0.035 in.).END BY:a) install pistonsb) install flywheel housingc) install timing gear coverd) install oil pump
Parts engine JOHNSON:
0284138
0284138 ENGINE COVER ASSY.
J40EENJ, J40EERE, J40EETB, J48ESLENB, J48ESLENB, J48ESLERD, J48ESLERD, J50BEENJ, J50BEERE, J50BEETB
0284185
0284185 ENGINE COVER ASSY., 48 MODELS
J48ESLENB, J48ESLENB, J48ESLERD, J48ESLERD, J48ESLETE, J48ESLETE
0284525
0436270
0284717
0437257
0284925
0438564