0436520 JOHNSON ENGINE COVER ASSY.


0436520 ENGINE COVER ASSY. JOHNSON J120TLARC, J125ESXERK, J140CXARC ENGINE
0436520 ENGINE COVER ASSY. JOHNSON
Rating:
43

Buy ENGINE COVER ASSY. 0436520 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

BRP JOHNSON entire parts catalog list:

J120TLARC, J120TLARK, J120TLERC, J120TLERK, J120TXARC, J120TXARK, J120TXERC, J120TXERK 1994
J125ESXERK 1994
J140CXARC, J140CXARK, J140CXERE, J140CXERK, J140TLARK, J140TLARR, J140TLERK, J140TLERR, J140TXARC, J140TXARK, J140TXERK, J140TXERR 1994

Information:

1. Disconnect connector (1). 2. Attach Tool (A) and fasten a hoist.3. Remove four bolts (3) and stack (2). The weight of the stack and hardware is 45 kg (100 lb). 4. Remove hose clamp (6).5. Remove five bolts (5) and support (4).6. Repeat Steps 4 and 5 for the other side of the engine. 7. Remove six bolts (7) that connect oil pan (8) to flywheel housing (9). Loosen the rest of the bolts that hold the oil pan in position. 8. Attach Tool (A) to the flywheel housing and a hoist. 9. Lift the end of the engine enough so a 1/2 in. Hardened Washer (10) can be installed on each side of the engine between the oil pan and the cylinder block.10. Install blocks under the oil pan to support the engine when the flywheel housing is removed. Lower the engine onto the blocks. 11. Remove twenty one bolts (11) and flywheel housing (9). The weight of the flywheel housing is 91 kg (200 lb).Install Flywheel Housing
1. Install two 1/2 -13 NC × 4 in. Long Guide Bolts in the cylinder block. Make sure gasket (12) is in position. The cylinder block, both sides of gasket (12) and the surface of the flywheel housing that makes contact with the gasket must not have any oil, fuel, water or gasket adhesive on them when the flywheel housing is installed on the engine.2. Install Tool (A) on the flywheel housing. Install flywheel housing (9) on the engine. The weight of the flywheel housing is approximately 91 kg (200 lb). Leave Tool (A) attached.
Torque Sequence Put 9S-3263 Thread Lock on bolts (17) through (20) before installation.3. Install the bolts that hold the flywheel housing in place.4. Use the following procedure to tighten the bolts: a. Tighten bolts 1 through 8 in number sequence to 136 14 N m (100 10 lb ft).b. Tighten bolts 9 through 20 in number sequence to 55 7 N m (41 5 lb ft).c. Again, tighten bolts 1 through 8 in number sequence to 136 14 N m (100 10 lb ft).d. Again, tighten bolts 9 through 20 in number sequence to 55 7 N m (41 5 lb ft). If a new gasket is installed, cut the ends of the gasket so it is even with the bottom of the cylinder block.5. Use Tool (A) and a hoist to lift the flywheel housing and engine enough so that the washers between the oil pan and the cylinder block can be removed. 6. Tighten the bolts that hold the oil pan to the cylinder block. Install six bolts (7) that hold oil pan (8) to flywheel housing (9). 7. Install support (4) with five bolts (5). Install clamp (6) to a torque of 7.0 1.5 N m (5 1 lb ft).8. Repeat Step (7) for the other side of the engine. 9. Use Tool (A) to lift stack (2) in place. Install the stack to the engine with four bolts (3). 10. Connect connector (1).End By:a. install crankshaft rear seal and wear sleeveb. install all turbochargers


Parts engine JOHNSON:

0432782
ENGINE COVER & SEAL ASSY., Stbd.
0432782 ENGINE COVER & SEAL ASSY., Stbd.
BJ130PLEED, BJ130PLSSS, BJ130TLECE, BJ130TLEDM, BJ130TLEUB, J120TLAEM, J120TLAIE, J120TLAND, J120TLARC, J120TLASB, J120TLATF, J125ESXENR, J125ESXERK, J125ESXESS, J125ESXETA, J125ESXW, J125WTPLE, J130CXAOR, J140CXARC, J140CXATF, J140CXCEC, J140CXEIA,
0434390
ENGINE COVER, Port
0434390 ENGINE COVER, Port
BJ130PLEED, BJ130PLSSS, BJ130TLECE, BJ130TLEDM, BJ130TLEUB, J120TLAIE, J120TLAND, J120TLARC, J120TLATF, J125ESXENR, J125ESXERK, J125ESXETA, J125WTPLE, J130CXAOR, J140CXARC, J140CXATF, J140CXEIA, J140CXENM, J185ESXENR, J200CXEIB, J200CXENE, J225CXEIC,
0434915
 
0434915 ENGINE COVER ASSY., Johnson, silver cover
J120TLAND, J120TLARC, J120TLATF, J125ESXENR, J125ESXERK, J125ESXETA, J140CXARC, J140CXATF, J140CXENM
0284112
 
0284112 ENGINE COVER ASSY., Evinrude
J120TLAND, J120TLARC, J120TLATF, J125ESXENR, J125ESXERK, J125ESXETA, J140CXARC, J140CXATF, J140CXENM
0284445
 
0284445 ENGINE COVER ASSY.
J120TLARC, J120TLATF, J125ESXERK, J125ESXETA, J140CXARC, J140CXATF
0284416
 
0284416 ENGINE COVER ASSY.
J120TLARC, J120TLATF, J125ESXERK, J125ESXETA, J140CXARC, J140CXATF
0284483
 
0284483 ENGINE COVER ASSY.
J120TLARC, J120TLATF, J125ESXERK, J125ESXETA, J140CXARC, J140CXATF
0284439
 
0284439 ENGINE COVER ASSY.
J120TLARC, J120TLATF, J125ESXERK, J125ESXETA, J140CXARC, J140CXATF
Back to top