0437173 JOHNSON ENGINE COVER ASSY., Jo.


0437173 ENGINE COVER ASSY., Jo. JOHNSON BJ3REDS, BJ4BREDS, J3REOD, J4REOD ENGINE
0437173 ENGINE COVER ASSY., Jo. JOHNSON
Rating:
13

Buy ENGINE COVER ASSY., Jo. 0437173 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

BRP JOHNSON entire parts catalog list:

BJ3REDS, SJ3REDS 1996
BJ4BREDS, BJ4BRLEDS, BJ4REDS, BJ4RLEDS, J4REDS, J4RLEDS, SJ4REDS, SJ4RLEDS 1996
J3REOD 1995
J4REOD, J4RLEOD 1995

Information:

1. Remove the rings from the pistons with tool (A). 2. Remove retaining ring (3), piston pin (1) and connecting rod (2) from the piston.3. Remove the bearings from the crankshaft end of the connecting rod.4. See USE OF PISTON PIN BEARING REMOVAL AND INSTALLATION TOOLS, SPECIAL INSTRUCTIONS, Form No. SMHS7295-02 for more information about removal and installation of piston pin bearings. Be sure to remove the bearings from the crankshaft end of connecting rod.5. Heat the connecting rod in an oven to a temperature of 350 to 500°F (176 to 260°C). Never use a direct flame to heat a connecting rod. 6. Put 6V3029 Spacer (11) in the base plate. Put the connecting rod on the base plate of tooling (B).7. Put the connecting rod piston pin bearing end in the center of the port assembly of tooling (B). Install pin (6) in the center of the bore for the connecting rod bearing.8. Install 6V2049 Adapter (9). Put the hole in the adapter in alignment with the hole in the base plate of tooling (B.9. Install clamp bar (10) and clamp pin (7). The old bearing is pushed out by tooling (B) as the new bearing is installed.10. Put 5P8645 Pusher Adapter (8) in position as shown with the taper side down. The piston pin bearing joint must be in alignment with the hole in adapter (9) and the base plate of tooling (B).11. Put pusher (4) on adapter (8).12. Use tooling (B) to push the new piston pin bearing (5) into the connecting rod until adapter (8) of tooling (B) makes full contact with the connecting rod surface.13. Remove the connecting rod and the old piston pin bearing from tooling (B).14. Check the piston pin bearing bore diameter after the bearing is installed. The correct dimension is 1.7012 .0003 in. (43.210 0.008 mm). The maximum permissible clearance between the bearing and piston pin (worn) must not be more than .003 in. (0.08 mm).Assemble Pistons
1. When old pistons are used, clean the piston grooves with an acceptable ring groove tool.2. Install the connecting rod bearings in the crankshaft end of the connecting rod. Make sure the tabs on the back of the bearings are in the tab grooves of the connecting rod and cap. 3. Put connecting rod (2) in position in the piston with bearing tab groove (3) and number identification on the same side as the "V" mark on the top of the piston.4. Install piston pin (1) and retaining ring (4).5. For correct piston and ring clearances, see PISTONS AND RINGS in SPECIFICATIONS.6. Install the oil ring spring in the oil ring groove of the piston. The oil ring must be installed on the piston with the ring end gap 180° from the oil ring spring joint. 7. Install the oil ring on the piston with tool (A).8. Install the intermediate piston ring with the side that has the mark "UP-2" toward the top of the piston with tool (A).9. Install the top piston ring with the side that has the mark "UP-1" toward the top of the piston. Make sure piston ring end gaps are 90° apart before the pistons are installed.end by: a) install pistons


Parts engine JOHNSON:

0435136
 
0435136 ENGINE COVER ASSY., Jo.
BJ3REDS, BJ4BREDS, J3RENM, J3REOD, J3RERE, J3RETB, J4RENM, J4REOD, J4RERE, J4RETB
0435138
 
0435138 ENGINE COVER ASSY., Jo.
BJ3REDS, BJ4BREDS, J3RENM, J3REOD, J3RERE, J3RETB, J4RENM, J4REOD, J4RERE, J4RETB
0435137
 
0435137 ENGINE COVER ASSY., Jo.
BJ3REDS, BJ4BREDS, J3REOD, J4REOD
0284691
 
0284691 ENGINE COVER ASSY., Ev.
BJ3REDS, BJ4BREDS, BJ4BREUC, J3REOD, J3REUC, J4REOD
0284692
 
0284692 ENGINE COVER ASSY., Ev.
BJ3REDS, BJ4BREDS, BJ4BREUC, J3REOD, J3REUC, J4REOD
0437177
 
0437177 ENGINE COVER ASSY., Jo.
BJ3REDS, BJ4BREDS, J3REOD, J4REOD
0284693
 
0284693 ENGINE COVER ASSY., Ev.
BJ3REDS, BJ4BREDS, BJ4BREUC, J3REOD, J3REUC, J4REOD
0342188
 
0342188 ENGINE COVER, Lower, Jo., front
BJ3REDS, BJ4BREDS, J3REOD, J4REOD, J4RLSIB
Back to top